Abstract:The Schockley–Quisser (SQ) limit of 28.64% is distant from the Sb 2 S 3 solar cells' record power conversion efficiency ( PCE ), which is 8.00%. Such poor efficiency is mostly owing to substantial interface-induced recombination losses caused by defects at the interfaces and misaligned energy levels. The endeavor of this study is to investigate an efficient Sb 2 S 3 solar cell structure via accurate analytical modeling. The proposed model considers different recombination mechanisms such as non-radiative recombination, Sb 2 S 3 /CdS interface recombination, Auger, SRH, tunneling-enhanced recombination, and their combined impact on solar cell performance. This model is verified against experimental work (Glass/ITO/CdS/Sb 2 S 3 /Au) where a good coincidence is achieved. Several parameters effects such as thickness, doping, electronic affinity, and bandgap are scrutinized. The effect of both bulk traps located in CdS and Sb 2 S 3 on the electrical outputs of the solar cell is analyzed thoroughly. Besides, a deep insight into the effect of interfacial traps on solar cell figures of merits is gained through shedding light into their relation with carriers' minority lifetime, diffusion length, and surface recombination velocity. Our research findings illuminate that the primary contributors to Sb 2 S 3 degradation are interfacial traps and series resistance. Furthermore, achieving optimal band alignment by fine-tuning the electron affinity of CdS to create a Spike-like conformation is crucial for enhancing the immunity of the device versus the interfacial traps. In our study, the optimized solar cell configuration (Glass/ITO/CdS/Sb 2 S 3 /Au) demonstrates remarkable performance, including a high short-circuit current ( J SC ) of 47.9 mA/cm 2 , an open-circuit voltage ( V OC ) of 1.16 V, a fill factor ( FF ) of 54%, and a notable improvement in conversion efficiency by approximately 30% compared to conventional solar cells. Beyond its superior performance, the optimized Sb 2 S 3 solar cell also exhibits enhanced reliability in mitigating interfacial traps at the CdS/Sb 2 S 3 junction. This improved reliability can be attributed to our precise control of band alignment and the fine-tuning of influencing parameters.

Quasiepitaxy Strategy for Efficient Full‐Inorganic Sb2S3 Solar Cells

Magnetron Sputtered Sb2Se3-based Thin Films Towards High Performance Quasi-Homojunction Thin Film Solar Cells

Recent Advances and Prospects of Solution‐Processed Efficient Sb2S3 Solar Cells

Confined‐space selenium assisted tellurization post‐treatment strategy for efficient full‐inorganic Sb2S3 thin film solar cells

Hydrazine Hydrate‐Induced Surface Modification of CdS Electron Transport Layer Enables 10.30%‐efficient Sb2(S,Se)3 Planar Solar Cells

Self-assembled growth of quasi-vertically oriented Sb2S3 thin films for substrate structured solar cells

A Novel Multi‐sulfur Source Collaborative Chemical Bath Deposition Technology Enables 8%‐efficiency Sb2S3 Planar Solar Cells

Grain Engineering of Sb2S3 Thin Films to Enable Efficient Planar Solar Cells with High Open‐Circuit Voltage

Enhanced charge carrier transport via efficient grain conduction mode for Sb2Se3 solar cell applications

Orientation control of close-spaced sublimation processed Sb2S3 thin films for efficient and stable planar solar cells

A Novel Multi-Sulfur Source Collaborative Chemical Bath Deposition Technology Enables 8%-Efficiency Sb2 S3 Planar Solar Cells.

Efficient CdS/Sb 2 S 3 interfacial modification using sodium borohydride etching for enhanced performance of low-cost full-inorganic antimony-based solar cells

Towards high-efficiency planar heterojunction antimony sulfide solar cells

n-Type Doping of Sb2S3 Light-Harvesting Films Enabling High-Efficiency Planar Heterojunction Solar Cells.

Suppressing Buried Interface Nonradiative Recombination Losses Towards High‐efficiency Antimony Triselenide Solar Cells

Heterostructured CdS Buffer Layer for Sb2Se3 Thin Film Solar Cell

Solution-processed SnO2 interfacial layer for highly efficient Sb2Se3 thin film solar cells

Quasi-Vertically Oriented Sb 2 Se 3 Thin-Film Solar Cells with Open-Circuit Voltage Exceeding 500 mV Prepared via Close-Space Sublimation and Selenization

Scrutinizing transport phenomena and recombination mechanisms in thin film Sb2S3 solar cells

A bithiophene-cored interfacial passivating layer for Sb2S3 solar cells with 7.1% efficiency

Regulating Energy Band Alignment via Alkaline Metal Fluoride Assisted Solution Post‐Treatment Enabling Sb 2 (S,Se) 3 Solar Cells with 10.7% Efficiency