Abstract:Nb-Si base alloys have attracted considerable attentions as the potential high temperature structural materials working in the service temperature range of 1200 similar to 1400 degrees C because of their high melting points (>1750 degrees C), moderate densities (6.6 similar to 7.2 g/cm(3)) and excellent high temperature strength. However, the mismatching between room temperature fracture toughness and high temperature strength has limited their practical applications. Directional solidification (DS) and alloying have been proved to be the effective methods to overcome this critical issue. The DS processes used to prepare Nb-Si base alloys included Czochralski directional solidification in a copper crucible, electron beam directional solidification, optical floating zone melting, integrally directional solidification and electromagnetic cold crucible directional solidification (ECCDS). The previous studies focused on the effect of process parameters on microstructure and mechanical properties in the steady-state growth region (SSGR). However, the microstructure in the SSGR was controlled by the solid-liquid interface, and the solid-liquid interface was controlled by process parameters. Therefore, the study about the effect of process parameters on solid-liquid interface was very important. In this work, the master alloy with the nominal composition of Nb-22Ti-16Si-3Cr-3Al-2Hf (atomic fraction, %) was prepared by vaccum non-consumable arc-melting first, and then induction skull melting. The DS experiments were performed in the ECCDS device equipped with a square water cooled copper crucible (internal dimension; 26 mmx26 mmx120 mm) and a Ga-In alloy pool. There were three processing parameters in ECCDS including heating power of power supply, withdrawal rate and holding time. The DS ingots were prepared according to the orthogonal test (L-9(3(3))). Instability degree was defined as the ratio of the height of solid-liquid interface to the width of the DS ingot. The results showed that there were three macroscopic morphologies of solid-liquid interfaces; the increase of holding time, decrease of withdrawal rate and elevation of heating power were conducive to keeping the solid-liquid interface macroscopic morphology planar. With the increase of withdrawal rate, primary dendrite arm spacing. (d(1)) and secondary dendrite arm spacing (d(2)) decreased gradually; with the increase of heating power, d(1) and d(2) increased gradually; with the increase of holding time, d(1) and d(2) increased first and then decreased. The higher withdrawal rate, lower heating power and less holding time were beneficial to refining the d(1) and d(2).

Microstructural Characterization of Integrally Directionally Solidified Nb-Si Based Alloys at High Withdrawal Rates

Microstructure evolution and solidification behaviour of Nb–16Si–22Ti–2Cr–2Al–6Hf alloy processed by directional solidification

Effect of solidification parameters on the microstructures of a single crystal Ni-based superalloy AM3

Dependency of Microstructure and Microhardness on Withdrawal Rate of Ti-43Al-2Cr-2Nb Alloy Prepared by Electromagnetic Cold Crucible Directional Solidification

Effects Of Withdrawal Rate On The Microstructure Of Directionally Solidified Gh4720li Superalloys

Effect of Withdrawal Rate on Microstructure and Mechanical Properties of a Directionally Solidified NiAl-based Hypoeutectic Alloy Doped with Trace Hf and Ho

The Effects of Withdrawal and Melt Overheating Histories on the Microstructure of a Nickel-Based Single Crystal Superalloy

Effect of Processing Parameters on Solid-Liquid Interface of Nb-Si Base Alloy Fabricated by Electromagnetic Cold Crucible Directional Solidification

Influence of Withdrawal Rate on Last Stage Solidification Path of a Mo-rich Ni3Al Based Single Crystal Superalloy

Dependence of microstructure and mechanical properties on solidification condition of directionally solidified Zn-55Al-1.6Si alloys

Solidification characteristics and high temperature tensile properties of Ni-based superalloy IN713C

Microstructure Evolution of Directionally Solidified Al-12%Ni Hypereutectic Alloy

Influence of Withdrawal Rate on the Microstructure of Ni-base Single-Crystal Superalloys Containing Re and Ru

Effect of Growth Rate on the Tensile Properties of DS NiAl/Cr(Mo) Eutectic Alloy Produced by Liquid Metal Cooling Technique

Effect of withdrawal rate on microstructure and lattice misfit of a Ni 3Al based single crystal superalloy

Microstructure and Microsegregation in A Ni-Based Single Crystal Superalloy Directionally Solidified under High Thermal Gradient

Microstructure Evolution of Directionally Solidified Al-25at.%Ni Peritectic Alloy

Characterization of the Microstructure Evolution and Microsegregation in A Ni-Based Superalloy under Super-High Thermal Gradient Directional Solidification

Microstructure of the Nb-Si Based Multicomponent Alloy by Electromagnetic Cold Crucible Directional Solidifcation

Effect of Directional Solidification Variables on the Microstructures of Single-Crystal Turbine Blades of Nickel-Based Superalloy

Ternary eutectic growth and associated tensile properties of directionally solidified Al87Si11Ni2 alloy