Abstract:Anion exchange membrane water electrolysis (AEMWE) is operated in an alkaline environment and has a similar membrane-electrode assembly (MEA) structure to that of proton exchange membrane water electrolysis (PEMWE). The use of non-noble metals as the electrocatalysts and operation at high current densities are inherently possible, so they are expected to be low-cost, high-performance candidates for next-generation water electrolysis systems. Improving the anion conductivity of the AEM and the activity of the non-precious metal catalysts is essential for the practical application of AEMWEs. 1 The non-noble electrocatalysts used in the MEA in this study were Ni 0.8 Co 0.2 O 2 and Ni 0.8 Fe 0.2 O, 3 which have a fused-aggregate network structure, and the electrolyte was a hydrocarbon-based AEM (QPAF-4) 4 , all of which were developed at the University of Yamanashi. The catalyst ink for the anodes was prepared by mixing the Ni 0.8 Co 0.2 O catalyst (University of Yamanashi) with solvent (water/methanol) and QPAF-4 (IEC = 2.0 meq g -1 , University of Yamanashi) binder solution. The anode ink was coated by using pulse-swirl-spray (PSS, Nordson) on the QPAF-4 membranes (IEC = 1.5 meq g -1 ) to make the catalyst-coated membranes (CCMs) with the anode. Catalyst inks for the cathodes was prepared by mixing Ni 0.8 Fe 0.2 O catalyst (University of Yamanashi) or Pt/CB catalyst (TEC10E50E, Tanaka Kikinzoku) with solvent (water/methanol) and QPAF-4 (IEC = 2.0 meq g -1 ) binder solution. The cathode ink was coated by using PSS on the gas diffusion layer (GDL, TGP-H-120, Toray) to make the gas diffusion electrodes (GDEs) for the cathodes. Ni mesh (Bekaert.co.jp) was used for the anode GDLs. The single cell (Figure 1, cell structure developed by Yokohama National University) performances were measured while supplying 1 M KOH at 80 °C to both electrodes. Figure 2 (a) shows the I-V performance of cells using Ni 0.8 Co 0.2 O for the anode and Ni 0.8 Fe 0.2 O or Pt/CB for the cathode. The electrolysis voltage observed for the cell with non-noble metal catalysts on both electrodes was higher than that for the cell with Pt/C on the cathode but was below 2 V at a current density of 1.2 A cm -2 . The value of the onset electrolysis voltage was nearly the same as that of the corresponding rotating disk electrode, 3 suggesting that the intrinsic performance of the cathode catalyst is being realized in the MEA. Increasing the amount of the cathodic catalyst loading scarcely affected the polarization. It is supposed that the fused-aggregate network structure of the Ni 0.8 Fe 0.2 O catalyst contributes to the favorable mass transfer. Figure 2 (b) shows the time dependence of the cell voltage of these cells. The increased loading amount improved the durability of the cathode. It is considered that the increase in the thickness of the cathode catalyst layer alleviated the damage of the GDL fibers to the membrane. These results indicate the possibility of adopting non-precious metal catalysts for both electrodes in AEMWE and thereby significantly reducing the catalyst cost. Acknowledgement This work was partially supported by NEDO of Japan through the AWE-1 project. References 1) A. Lim et al., J. Ind. Eng. Chem ., 76 , 410 (2019). 2) G. Shi et al., ACS Catal ., 12 , 14209 (2022). 3) G. Shi et al., ACS Omega , 8 , 13068 (2023). 4) H. Ono et al., J. Mater. Chem . A , 5 , 24804 (2017). Figure 1

A Study on Electrode Fabrication and Operation Variables Affecting the Performance of Anion Exchange Membrane Water Electrolysis

Alkaline anion exchange membrane water electrolysis: Effects of electrolyte feed method and electrode binder content

Influence of Contact Pressure and Flow Rate on the Performance of Anion Exchange Membrane Electrolysis

Understanding the Effects of Anode Catalyst Conductivity and Loading on Catalyst Layer Utilization and Performance for Anion Exchange Membrane Water Electrolysis

Performance and Durability of Membrane-Electrode Assemblies Using Non-Precious Metal Catalyst and a Hydrocarbon-Based Electrolyte for Anion Exchange Membrane Water Electrolysis

(Invited) Progress and Perspective Towards Low-Cost High-Performance Anion Exchange Membrane Water Electrolysis

Performance of Anion Exchange Membrane Water Electrolysis with High Ionic Strength Electrolyte

Factors in electrode fabrication for performance enhancement of anion exchange membrane water electrolysis

Performance and Durability of Pure-Water-Fed Anion Exchange Membrane Electrolyzers Using Baseline Materials and Operation

Advanced development of anion-exchange membrane electrolyzers for hydrogen production: from anion-exchange membranes to membrane electrode assemblies

Electrochemical Performance Modeling of A Proton Exchange Membrane Electrolyzer Cell for Hydrogen Energy

Membrane electrode assembly simulation of anion exchange membrane water electrolysis

Comprehensive study and optimization of membrane electrode assembly structural composition in proton exchange membrane water electrolyzer

(Invited) Current Status and Progress in Anion Exchange Membrane Electrolysis

Anion exchange membrane water electrolysis: Numerical modeling and electrochemical performance analysis

Anion Exchange Membrane Water Electrolysis at 10 A·cm‐2 Over 800 Hours

Mechanical and Physio-Chemical Properties of Anion Exchange Membranes and Their Implications on Industrial Scale Water Electrolysis

(Digital Presentation) Diagnostic Study of the Key Performance-Limiting Factors in Anion Exchange Membrane Fuel Cells

Anisotropic polyphenylene-based anion exchange membranes with flexible side chains via click reaction for high performance water electrolysis

Comprehensive impedance investigation of low-cost anion exchange membrane electrolysis for large-scale hydrogen production

Engineering Robust Triazine Crosslinked and Pyridine Capped Anion Exchange Membrane for Advanced Water Electrolysis