Abstract:In this work, a thorough study on the effects of sulfur-addition in the Cu50Zr50 glass-forming system was conducted using laboratory-based X-ray diffraction (XRD), synchrotron-based high-energy XRD (HESXRD), differential scanning calorimetry, and uniaxial compression testing. We report that the glass-forming ability (GFA), thermal stability, phase transformation sequence during heating and cooling, as well as the mechanical properties of the Cu50Zr50 system are highly sensitive to the sulfur concentration. Proper addition of sulfur can not only stabilize the B2-CuZr phase, but also enhances the GFA of the system. This enables the formation of BMG composites that solely contain a B2 phase, which results in a combination of high strength and substantial plastic strain under compressive loading. The total strains of the newly developed BMG composites with sulfur contents of 0.5 and 1.0 at.% are as large as ∼10 at.%, exceeding the previously reported strains of the Cu50Zr50 BMG by far. These superior properties make the Cu-Zr-S BMG composites a promising candidate material for industrial applications. In addition, it is found that excessive addition of sulfur leads to the precipitation of the Cu10Zr7 phase upon cooling from the alloy melt and a sulfide phase during heating from the glassy state. HESXRD experiments suggest that the preferential bonding between Zr and S atoms could be the determining structural mechanism on the atomic scale, leading to the changing primary crystallization sequence for heating and cooling. The findings in this work further strengthen the high relevance of sulfur in alloy development and tuning of properties in BMGs, especially considering the low cost, good availability, and non-toxicity of sulfur in the relevant modifications.

Tribological Behaviors of Self‒mated Cu36Zr48Ag8Al8 Bulk Metallic Glass under H2SO4 Conditions with Different Concentrations

Sliding Friction and Wear Mechanisms of Cu36Zr48Ag8Al8 Bulk Metallic Glass under Different Sliding Conditions: Dry Sliding, Deionized Water, and NaOH Corrosive Solutions

Tribological properties of Ti40Zr25Ni8Cu9Be18 bulk metallic glasses under different conditions

In-situ Fabricated Bulk Metallic Glass/graphite Composites with a 3D Lubricating Layer: Tribological Properties under Dry Sliding and in Seawater

Passivation Behavior of a Zr60Cu20Ni8Al7Hf3Ti2 Bulk Metallic Glass in Sulfuric Acid Solutions

Corrosive wear behaviors and mechanisms of a biocompatible Fe-based bulk metallic glass

Thermal Oxidation Effect on Corrosion Behavior of Zr46Cu37.6Ag8.4Al8 Bulk Metallic Glass

Effects of normal load and reciprocating frequency on the tribological behaviors of a Zr-based bulk metallic glass

The Tribological Behaviors in Zr-Based Bulk Metallic Glass with High Heterogeneous Microstructure

Microstructure and Tribological Behavior of Mg–Gd–Zn–Zr Alloy with LPSO Structure

Tribological Behavior of Si3N4 - Hbn Ceramic Materials Against Stainless Steel under Dry Friction Condition

Corrosion mechanisms of Zr-based bulk metallic glasses in NaBr solution

Wear Behavior of A Series of Zr-Based Bulk Metallic Glasses

Enhanced wear, corrosion, and corrosive-wear resistance of the biocompatible Ti-based bulk metallic glass by oxidation treatment

Mechanical and tribological properties of Zr–Cu–Ni–Al bulk metallic glasses with dual-phase structure

Enhancing the tribological performance of the TiZrHfCuBe high entropy bulk metallic glass by Sn addition

Spectroscopic evaluation of tribologically-induced changes in surface chemistry of Zr-based bulk metallic glass

Tribological and Corrosion Behaviors of Zr-doped Graphite-Like Carbon Nanostructured Coatings on Ti6Al4V Alloy

Effect of Heat Treatment on Tribological Properties of SiCp/Al–Mg–Mn–Cu Aluminum Matrix Composites

Investigation of Tribological and Mechanical Performances of Ti‐based Self‐Lubricating Composites Containing SnAgCu and Al2O3

Influence of sulfur addition on the glass formation, phase transformation and mechanical properties of Cu50Zr50 alloy