Abstract:Vapor deposition of perovskite solar cells (PSCs) has attracted considerable interest for its dry processing characteristics. However, a two-step sequential vapor deposition method suffers from ineffective conversion of PbI2 to perovskite with reasons still unclear. In this report, we carefully investigated the crystallization orientation of PbI2 films deposited by physical vapor deposition via synchrotron grazing-incidence wide-angle X-ray scattering (GIWAXS) and observed an asymmetric scattering pattern with respect to the qz-axis. The observed oriented morphology and texture hinder the diffusion of MAI molecules in the PbI2 films synthesized by vapor deposition, resulting in over 15% PbI2 remaining at the buried interface after reaction with MAI vapor. As a result, the MAPbI3 synthesized in this way was also highly oriented, especially in the surface layers. Surface fumigation (SF) step was introduced to decrease the orientational anisotropy of PbI2, which successfully breaks the diffusion barriers of MAI molecules by forming a complex layer on the PbI2 surface with polar solvent vapors, like dimethyl sulfoxide or 1,3-dimethyl-2-imidazolidinone. We infer that the SF treatment changes the vapor–solid reaction mechanism from reaction–crystallization to dissolution–recrystallization, which largely promotes the conversion of PbI2 to perovskite. Defects were reduced in perovskite synthesized in this way, and a p-i-n device with 19.56% efficiency was fabricated, which is among the highest efficiencies reported for sequential-vapor-deposited PSCs. Notably, this method enables the fabrication of conformal perovskite layers on uneven substrates. An exemplary PSC showing efficiency of 8.93% was fabricated on a precurved substrate. We believe that the method is applicable to the fabrication of tandem or curved PSCs that are compatible with wearable or building/autocar-integrated photovoltaics in the future.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.1c12283.XRD, SEM, GIWAXS, coordination rate test, diagram of saturated vapor pressure, stability of different complexes, MAI loss rate, film color changes during the reaction, comparison of the efficiency, J–V curves, steady-state output at the maximum power point, the corresponding external quantum efficiency (EQE) spectra in the literature (PDF)This article has not yet been cited by other publications.

Resolving the Detrimental Interface in Co-Evaporated MAPbI3 Perovskite Solar Cells by Hybrid Growth Method

Interfacial Engineering of Perovskite Solar Cells with Evaporated PbI 2 Ultrathin Layers

Vacuum Co-Deposited CH3NH3PbI3 Films by Controlling Vapor Pressure for Efficient Planar Perovskite Solar Cells

Importance of methylammonium iodide partial pressure and evaporation onset for the growth of co-evaporated methylammonium lead iodide absorbers

Crystallization and Defect Chemistry Dual Engineering for MAPbI 3 Perovskite Solar Cells with Efficiency Approaching 22%

Synchronous Elimination of Excess Photoinstable PbI2 and Interfacial Band Mismatch for Efficient and Stable Perovskite Solar Cells

Surface-Orientation Elimination of Vapor-Deposited PbI 2 Flakes for Efficient Perovskite Synthesis on Curved Solar Cells

All-in-One Deposition to Synergistically Manipulate Perovskite Growth for High-Performance Solar Cell

A Modified Sequential Deposition Route for High-Performance Carbon-Based Perovskite Solar Cells under Atmosphere Condition

Controllable Blading Interdiffusion of Formamidinium Iodide on Thermal Evaporated Scalable and Conformal Lead Iodide for Efficient Perovskite Solar Cells

Suppressing Ion Migration by Synergistic Engineering of Anion and Cation towards High‐Performance Inverted Perovskite Solar Cells and Modules

Hybrid perovskite films deposited by thermal evaporation from a single source

Grain Boundary Elimination via Recrystallization‐Assisted Vapor Deposition for Efficient and Stable Perovskite Solar Cells And Modules

2D PEA 2 PbI 4 –3D MAPbI 3 Composite Perovskite Interfacial Layer for Highly Efficient and Stable Mixed-Ion Perovskite Solar Cells

Interface optimization and growth control for high efficiency wide bandgap perovskite solar cells

Understanding and exploiting interfacial interactions between phosphonic acid functional groups and co-evaporated perovskites

Solution-Processing Interface Layers for High Performance Perovskite Solar Cells

Solvent-vapor assisted conversion process for hybrid perovskites coupling thermal evaporation and slot-die coating

Solvent‐Additive Engineering‐Assisted Improvement of Interface Contact for Producing Highly Efficient Inverted Perovskite Solar Cells

Enhancing the Efficiency and Stability of Triple-Cation Perovskite Solar Cells by Eliminating Excess PbI2 from the Perovskite/Hole Transport Layer Interface

Removing residual PbI2 on the perovskite surface for efficient solar cells