Abstract:Organometal halide perovskite is one of the most promising materials for high efficient thin-film solar cell. Solution fabrication process shows that the recorded power conversion efficiency (PCE) is 23.7%, however, large scale fabrication suffers the inevitable toxic solvent, preventing it from implementing the green commercialization. As one of the matured large-scale fabrication techniques, the vapor deposition is recently found to promise the green fabrication of perovskite thin film without toxic solvent. However, the PCE based on vapor deposition is considerably lower than that based on solution fabrication because of ineffective regulation methods of the perovskite films. So, there is intensive requirement for optimizing the growth of perovskite in vapor deposition for improving PCE, especially, developing a kind of quality regulation method of the perovskite films. In this study, we provide a method of adjusting grain size in vapor deposition method. The grain size optimization of MAPbI 3 films is realized by simply modulating the reaction temperature between PbI 2 films and MAI vapor. We set the reaction temperature to be 140 °C, 160 °C, 180 °C and 200 °C separately and establish the relationship between reaction time and grain size during the complete conversion of PbI 2 film into MAPbI 3 film. We find that the average grain size of the film increases first with growth temperature increasing from 140 °C to 180 °C and then decrease at 200 °C, giving an average grain size of 0.81 \begin{document}${\text{μm}}$\end{document} and a largest grain size of about 2 \begin{document}${\text{μm}}$\end{document} at 180 °C. The defect density of perovskite film is deduced from the space charge limited current model, showing that it decreases from 5.90 × 10 16 cm –3 at 140 °C to 2.66 × 10 16 cm –3 at 180 °C. Photovoltaic devices with structure FTO/TiO 2 /C 60 /MAPbI 3 /spiro-OMeTAD/Au are fabricated to demonstrate the performance. It is found that the devices with an active area of 0.045 cm 2 show that with the increase of grain size, the average PCE increases from 14.00% to 17.42%, and the best device shows that its PCE is 17.80% with 4.04% hysteresis index. To show the possibility of scaling up, we fabricate a uniform perovskite thin film with an area of about 72 cm 2 , and a device with an active area of 1 cm 2 , which gives a PCE of 13.17% in reverse scan. In summary, our research provides a method of regulating the grain size for the vapor deposition, which can improve device performance by reducing the trap density in perovskite film for suppressing the carrier recombination in grain boundary. Meanwhile, we prepare high performance devices and large area thin films, showing their potential in large area device fabrication and applications.

Grain Boundary Elimination via Recrystallization‐Assisted Vapor Deposition for Efficient and Stable Perovskite Solar Cells And Modules

A Polymerization‐Assisted Grain Growth Strategy for Efficient and Stable Perovskite Solar Cells

Crystalline Liquid-like Behavior: Surface-Induced Secondary Grain Growth of Photovoltaic Perovskite Thin Film

Chemical Sintering Reduced Grain Boundary Defects for Stable Planar Perovskite Solar Cells

Tailored Key Parameters of Perovskite for High-Performance Photovoltaics

Scalable Fabrication of High‐Performance Perovskite Solar Cell Modules by Mediated Vapor Deposition

Optimization of grain size to achieve high-performance perovskite solar cells in vapor deposition

Surface Reconstruction for Efficient and Stable Monolithic Perovskite/Silicon Tandem Solar Cells with Greatly Suppressed Residual Strain

Perovskite solar cells by vapor deposition based and assisted methods

In Situ Polymerization of Cross‐Linked Perovskite–Polymer Composites for Highly Stable and Efficient Perovskite Solar Cells

Vapor-Assisted Crystallization Control Toward High Performance Perovskite Photovoltaics With Over 18% Efficiency In The Ambient Atmosphere

Solvent-Free Method for Defect Reduction and Improved Performance of p-i-n Vapor-Deposited Perovskite Solar Cells

Enabling Full-Scale Grain Boundary Mitigation in Polycrystalline Perovskite Solids.

1,8‐Octanediamine Dihydroiodide‐Mediated Grain Boundary and Interface Passivation in Two‐Step‐Processed Perovskite Solar Cells

Interfacial modification engineering for efficient and stable MA-free wide-bandgap perovskite solar cells by grain regrowth

In Situ Grain Boundary Modification Via Two-Dimensional Nanoplates to Remarkably Improve Stability and Efficiency of Perovskite Solar Cells.

In situ self‐elimination of defects via controlled perovskite crystallization dynamics for high‐performance solar cells

Grain Boundary Modification via F4TCNQ To Reduce Defects of Perovskite Solar Cells with Excellent Device Performance

Efficient inorganic vapor‐assisted defects passivation for perovskite solar module

Multiple-Defect Management for Efficient Perovskite Photovoltaics

Insight into the Defect Chemistry and Ion Migration in Perovskite Fabricated by Hybrid Chemical Vapor Deposition