Abstract:Cold spray (CS), as a novel surface treatment technique, has been widely used for repairing damaged components and as protecting coatings, especially for the applications of aircraft and marine components. To further improve the mechanical properties, while maintaining the corrosion resistance of pure Al and Al alloy coatings, ceramic particles are commonly added into the Al matrix to produce particle-strengthened Al matrix composite (P-AMC) coatings. In this study, dense 7075Al composite coatings reinforced with uniformly distributed in-situ TiB2 nanoparticles (hereafter named TiB2/7075Al) were successfully produced by CS using a gas-atomized composite powder and the propulsive gases of air and helium. Following this, the corrosion behavior of the cold sprayed (CSed) TiB2/7075Al composites was investigated using Tafel polarization, electrochemical impedance, spectroscopy, and immersion tests in 0.1 M and 0.6 M NaCl solutions, and were compared to those of the CSed pure 7075Al coating and bulk 7075Al-T6 material. Electrochemical tests revealed that the composite coating exhibits a higher corrosion rate than the pure 7075Al coating, primarily caused by a galvanic coupling between TiB2 nanoparticles and the more active Al matrix. Compared to the air-processed coatings, the He-processed ones exhibit higher densities of defects, like dislocations, and precipitates due to larger plastic deformation of the sprayed particles, which result in more active sites for corrosion and thus lower corrosion resistance. Low-temperature annealing treatment (230 °C/6 h) reduces these defects to increase the corrosion resistance of the CSed coatings. Comparatively, high-temperature annealing treatment (412 °C/4 h) results in the coarsening of precipitates and grain growth to increase the corrosion rate of the coatings. Corrosion mechanisms of the CSed and annealed composite coatings related to the microstructure evolution were investigated in detail.

Corrosion Onset Associated with the Reinforcement and Secondary Phases in B4C-6061Al Neutron Absorber Material in H3BO3 Solution

Corrosion behavior and failure mechanism of amorphous Al2O3 coating at high-temperature LBE

Influence of particulate B4C with high weight fraction on microstructure and mechanical behavior of an Al-based metal matrix composite

The Corrosion Behavior of Al/Al2O3 Composite Films with Ultra-Dense Structure Exposed to Lead-Bismuth Eutectic at 450 to 650 °C

Thermally Stable Microstructures and Mechanical Properties of B4C-Al Composite with In-Situ Formed Mg(Al)B2

Corrosion and wear performance and mechanism study of ZrB2/AA6016

Microstructure and Durability of RC in Boric Acid

A novel B 4 C/Al-316 L neutron absorbing clad plate prepared by cold spraying: Microstructure and mechanical properties

Oxidation behavior of CrAl-Mo coated Zircaloy-4 in DB and BDB scenarios

The Effect of MoAlB Substitutions on the Oxidation Behavior of ZrB2-SiC Composites at 1600°C

Microstructure and Mechanical Properties of Al–B 4 C Composite at Elevated Temperature Strengthened with in Situ Al 2 O 3 Network

Influence of particulate B4C size on microstructural evolution and mechanical behavior in nanostructured Al matrix during heat treatment

High Temperature Mechanical Properties and Wear Performance of B4C/Al7075 Metal Matrix Composites

Electrochemical corrosion behavior of hot-pressing sintered WC-Al2O3 composite in alkaline and acidic solutions

Study of corrosion resistance of cold sprayed Al + B4C composite coatings

Microstructure, mechanical properties and corrosion behavior of AlxCrMoNbZr multiprincipal element alloy coatings for accident-tolerant fuel claddings: Effect of Al content

Synergistic Effect of Ex Situ and In Situ Reinforcements on the Dry Reciprocating Wear Behavior of AA6061-B4C Composite Fabricated Using Varying K2TiF6 Flux Content

Corrosion of New Zirconium Claddings in 500 °C/10.3 MPa Steam: Effects of Alloying and Metallography

High-temperature corrosion behavior of hot-pressed Al-based Gd2O3-W shielding materials used in spent fuel storage

Microstructure, wear and corrosion properties of B-C composite layers on pure titanium

Corrosion behavior of cold sprayed 7075Al composite coating reinforced with TiB2 nanoparticles