Abstract:A site-specific xenon plasma focused ion beam preparation technique for microcantilever samples (1-20 µm width and 1:10 aspect ratio) is presented. The novelty of the methodology is the use of a chunk lift-out onto a clean silicon wafer to facilitate easy access of a low-cost probe type indenter which provides bending force measurement. The lift-out method allows sufficient room for the indenter and a line of sight for the electron beam to enable displacement measurement. An electroplated nanotwinned copper (NTC) was cut to a 3 × 3 × 25 µm microbeam and in situ mechanically tested using the developed technique. It demonstrated measured values of Youngs modulus of 78.7 ± 11 GPa and flow stress of 0.80 ± 0.05 GPa, which is within the ranges reported in the literature. LAY DESCRIPTION: In this paper a site specific method is present for making particularly small mechanical tests samples, of the order of 100th the size of a human hair. These small samples can then be used to determine the mechanical properties of the bulk material. Copper with a nano twinned grain structure is used as a test medium. Ion milling was used to cut the sample to shape and a micro probe was used for mechanical testing. Ion milling can cut away very small volumes of material as it accelerates ions at the surface of the sample, atomically machining the sample. Micro probes are a cost-effective small-scale load measurement devices, however, they require a large area for accessing the sample. The indenter requirements are a problem when making you samples with ion milling as ion millers are best at making small cuts. Our aim was to design a cutting strategy which reduces the amount of cutting required while allowing samples to be fabricated anywhere on the sample. We used a chunk lift out technique to remove a piece of material which is then welded to a wafer of silicon this gives sufficient space around the sample for ion milling and testing. The additional space allowed easy access for the probe. A 3 × 3 × 10 µm micro cantilever beam was cut out from copper, this beam was then bent. The force from bending and distance bent was measured and converted into Youngs modulus which is a measure of flexibility. The modulus value measured was comparable to the values reported in other papers.

A probe-based force-controlled nanoindentation system using an axisymmetric four-beam spring

Fabrication of Ordered Micro/Nanostructures Using Probe-Based Force-Controlled Micromachining System

A Probe-Based Nanometric Morphology Measurement System Using Intermittent-Contact Mode

Development of a New Microscopic Four-Point AFM Probe for the Measurement of Local Electrical Conductivity

An Adaptive Nanoindentation System Based on Electric Bending of A Piezoelectric Cantilever

An Instrument for Measuring Mechanical Properties of MEMS Materials by Nanoindentation and Micro-Beam-Bending

Note: Nanomechanical characterization of soft materials using a micro-machined nanoforce transducer with an FIB-made pyramidal tip

Probe-Type Microforce Sensor for Mirco/Nano Experimental Mechanics

Three-Dimensional Nano Measurement System Based on Resonant Trigger Probe

Design and Fabrication of a Miniature Four-Axial Piezoresistive Force/Torque Sensor with MEMS Technology

Fabrication of a microscopic four-point probe and its application to local conductivity measurement

In Situ Nanoindentation Mechanical Property of Films by Atomic Force Microscope

A piezoelectric-driven nanoindentation system for scanning electron microscope with improved analog compensation method

Focused ion beam preparation of microbeams for in situ mechanical analysis of electroplated nanotwinned copper with probe type indenters

Micro/nano Scale Mechanical Tests Based on the Probe Platform

Design of A Large-Scanning-Range Contact Probe for Nano-Coordinate Measurement Machines

Measurement of mechanical properties of one-dimensional nanostructures with combined multi-probe platform

Three-Axis Micro-Force Sensor Based on a Mechanical Probe

A 3D-printed portable microindenter for mechanical characterization of soft materials.

A novel scanning force microscopy probe with thermal-electrical actuation and piezo-resistive sensing

A novel technique of microforce sensing and loading