Abstract:Using pyromelliticdianhydride (PMDA) and polyfunctional epoxy ether (PFE) as branching agent, long chain branching stereocomplex poly(L‐lactide)s and poly(D‐lactide)s was prepared by reactive processing, respectably. Then stereocomplex poly(lactide)s of long chain branching PLLA and PDLA (sc‐PLA/BA) was prepared by solution blending and its fabricated the vascular stents via 3D‐printing.The effects of branching structure on melt crystallization behavior of sc‐PLA/BA investigated by DSC. The influence of the branching agent content on the crystallization ability of samples shows a bell‐shaped relationship, there is a maximum point when the branching agent content is1.5 wt%. When the branching agent content is less than 1.5 wt%, the crystallization ability of the sample increased with the increasing of branching agent content. When the branching agent content exceeded than 1.5 wt%, the crystallization ability of the samples decreased with branching agent content increasing. Such behavior is as the linear PLA branched to dendrite configuration, the enrichment of segments around branching structure within branched chains promoted its nucleation. But the high degree of branching caused inter‐ or intrachians entanglement which obstructed the segments movement and growth into the crystals. The half‐time of crystallization (t1/2) of the samples decreased from 6 minutes for initial sc‐PLA/BA‐0 to 3 minutes of sc‐PLA/BA‐1.5 wt% at 163°C. POM results indicated that nucleation density of sc‐PLA/BA significantly increased with the branching agent increasing. Moreover, mechanical testing demonstrated that forming branching structure could be an effective modification of the mechanical properties for sc‐PLA, its tensile strength and modulus increases from 57.3 MPa and 2.02 GPa to 70.4 MPa and 3.31 GPa, respectively. TGA results analyzed by FWO method and Kissinger method, indicated the apparent activation energy of sc‐PLA/BA samples increases from 96.8 to 113.3 kJ/mol, suggesting the improvement of heat resistance. The CCK‐8 assay, ALP assay and cell Live/Dead assay results indicated that sc‐PLA with branching structure presented very low cell cytotoxicity. Therefore, the long chain branching sc‐PLA matrix with branching agent could effectively improve its crystallization abilities, mechanical properties, heat resistance and biocompatibilities.

The Preparation of Chain Branching PLLA by Intermolecular Hydrogen Bonding with 3-Pentadecylphenol and Its Crystallization, Relaxation Behavior and Thermal Stability

Blending Effects on Polymorphic Crystallization of Poly(l-lactide)

Poly(L-Lactide)/Layered Double Hydroxides Nanocomposites: Preparation and Crystallization Behavior

Competing Stereocomplexation and Homocrystallization of Poly(l-lactic Acid)/poly(d-Lactic Acid) Racemic Mixture: Effects of Miscible Blending with Other Polymers

Preferential Formation of Β-Form Crystals and Temperature-Dependent Polymorphic Structure in Supramolecular Poly(l-lactic Acid) Bonded by Multiple Hydrogen Bonds

Effect of Crystallization Temperature on Crystal Modifications and Crystallization Kinetics of Poly(l‐lactide)

Enhanced Crystallization Rate and Mechanical Properties of Poly(l‐lactic Acid) by Stereocomplexation with Four‐armed Poly(ϵ‐caprolactone)‐block‐poly(d‐lactic Acid) Diblock Copolymer

Enhancing Crystallization Behavior for Optimized Performances of Poly(tmc‐b‐(lla‐ran‐ga)) by PDLA/PLLA Stereocomplex Crystallization

Effect of POSS-NH2-grafted different plasticizers on the crystallization properties of SC-Poly (l-lactic acid)

Polymorphic Crystallization Behavior of a Poly(butylene adipate) Midblock within a Poly(L-lactide-butylene adipate-L-lactide) Triblock Copolymer

Stereocomplex Poly(lactic Acid) Vascular Stents by 3d‐printing with Long Chain Branching Structures: Toward Desirable Crystallization Properties and Mechanical Performance

Effect of Poly (3-hydroxybutyrate-co-3-hydroxyhexanoate) on the Crystalline Properties of Poly (L-lactic acid)

Synthesis of Tri-arm PLLA-PDLA Block Copolymers and Its Stereocomplex Crystallization Behavior

High Melt Performance Poly (lactic acid) with Dual Hybrid Long Branching Chains Prepared by Chain Degradation and Restructuring

Two-Stage Crystallization Kinetics and Morphological Evolution with Stereocomplex Crystallite-Induced Enhancement for Long-Chain Branched Polylactide/Poly(D-lactic Acid) Blends

Controlling stereocomplex crystal morphology in poly(lactide) through chain alignment

Relationship between the Stereocomplex Crystallization Behavior and Mechanical Properties of PLLA/PDLA Blends

Studies on Crystallization Kinetics of Bimodal Long Chain Branched Polylactides

Synthesis, Structures and Characterization of Triarm Ppo-Pdla-Plla Block Copolymers and Its Stereocomplex Crystallization Behavior

Thermal And Crystallinity Property Studies Of Poly (L-Lactic Acid) Blended With Oligomers Of 3-Hydroxybutyrate Or Dendrimers Of Hvdroxyalkanoic Acids

Promoting the formation of stereocomplex crystal in PLLA/PDLA by crosslinking restricted phase separation and solid-state stretching induced orientation