Abstract:Using pyromelliticdianhydride (PMDA) and polyfunctional epoxy ether (PFE) as branching agent, long chain branching stereocomplex poly(L‐lactide)s and poly(D‐lactide)s was prepared by reactive processing, respectably. Then stereocomplex poly(lactide)s of long chain branching PLLA and PDLA (sc‐PLA/BA) was prepared by solution blending and its fabricated the vascular stents via 3D‐printing.The effects of branching structure on melt crystallization behavior of sc‐PLA/BA investigated by DSC. The influence of the branching agent content on the crystallization ability of samples shows a bell‐shaped relationship, there is a maximum point when the branching agent content is1.5 wt%. When the branching agent content is less than 1.5 wt%, the crystallization ability of the sample increased with the increasing of branching agent content. When the branching agent content exceeded than 1.5 wt%, the crystallization ability of the samples decreased with branching agent content increasing. Such behavior is as the linear PLA branched to dendrite configuration, the enrichment of segments around branching structure within branched chains promoted its nucleation. But the high degree of branching caused inter‐ or intrachians entanglement which obstructed the segments movement and growth into the crystals. The half‐time of crystallization (t1/2) of the samples decreased from 6 minutes for initial sc‐PLA/BA‐0 to 3 minutes of sc‐PLA/BA‐1.5 wt% at 163°C. POM results indicated that nucleation density of sc‐PLA/BA significantly increased with the branching agent increasing. Moreover, mechanical testing demonstrated that forming branching structure could be an effective modification of the mechanical properties for sc‐PLA, its tensile strength and modulus increases from 57.3 MPa and 2.02 GPa to 70.4 MPa and 3.31 GPa, respectively. TGA results analyzed by FWO method and Kissinger method, indicated the apparent activation energy of sc‐PLA/BA samples increases from 96.8 to 113.3 kJ/mol, suggesting the improvement of heat resistance. The CCK‐8 assay, ALP assay and cell Live/Dead assay results indicated that sc‐PLA with branching structure presented very low cell cytotoxicity. Therefore, the long chain branching sc‐PLA matrix with branching agent could effectively improve its crystallization abilities, mechanical properties, heat resistance and biocompatibilities.

Enhancing Crystallization Behavior for Optimized Performances of Poly(tmc‐b‐(lla‐ran‐ga)) by PDLA/PLLA Stereocomplex Crystallization

Blending Effects on Polymorphic Crystallization of Poly(l-lactide)

Competing Stereocomplexation and Homocrystallization of Poly(l-lactic Acid)/poly(d-Lactic Acid) Racemic Mixture: Effects of Miscible Blending with Other Polymers

Fractionated Crystallization Kinetics and Polymorphic Homocrystalline Structure of Poly(L-lactic Acid)/poly(d-Lactic Acid) Blends: Effect of Blend Ratio

Research progress on stereocomplex crystallization of poly(lactic acid) enantiomeric blends

Enhancement of the crystallization and biocompatibility of poly(TMC-b-(LLA-ran-GA)) by poly(lactide) stereocomplex

Enhanced Crystallization Rate and Mechanical Properties of Poly(l‐lactic Acid) by Stereocomplexation with Four‐armed Poly(ϵ‐caprolactone)‐block‐poly(d‐lactic Acid) Diblock Copolymer

Enhancement of the properties of biodegradable poly(L-lactide)/poly(butylene carbonate) blends by introducing stereocomplex polylactide crystals

Enhancement of the crystallization and biocompatibility of poly(TMC-<i>b</i>-(LLA-<i>ran</i>-GA)) by poly(lactide) stereocomplex

Relationship between the Stereocomplex Crystallization Behavior and Mechanical Properties of PLLA/PDLA Blends

Significant Enhancement of Crystallization Kinetics of Polylactide in Its Immiscible Blends Through an Interfacial Effect from Comb-Like Grafted Side Chains

Toward Exclusive Stereocomplex Crystallization of High-Molecular-weight Poly(l-Lactic Acid)/poly(d-Lactic Acid) Blends with Outstanding Heat Resistance Via Incorporating Selective Nucleating Agents.

The Effect of Polyethylene Glycol on the Non-Isothermal Crystallization of Poly(L-lactide) and Poly(D-lactide) Blends

Synergistic effect of star‐shaped architecture and polyethylene glycol moieties on poly (lactic acid) stereocomplex crystallization behaviors

Enantiomeric Blends of High-Molecular-Weight Poly(Lactic Acid)/Poly(Ethylene Glycol) Triblock Copolymers: Enhanced Stereocomplexation and Thermomechanical Properties

Formation of Stereocomplex Crystal and Its Effect on the Morphology and Property of PDLA/PLLA Blends

Crystallization, thermal and mechanical properties of stereocomplexed poly(lactide) with flexible PLLA/PCL multiblock copolymer

Two-Stage Crystallization Kinetics and Morphological Evolution with Stereocomplex Crystallite-Induced Enhancement for Long-Chain Branched Polylactide/Poly(D-lactic Acid) Blends

Polymorphic Crystallization and Crystalline Reorganization of Poly(l-lactic acid)/Poly(d-lactic acid) Racemic Mixture Influenced by Blending with Poly(vinylidene fluoride)

The Accelerating Effect of the Star-Shaped Poly(d-Lactide)-block-poly(l-lactide) Stereoblock Copolymer on PLLA Melt Crystallization

Stereocomplex Poly(lactic Acid) Vascular Stents by 3d‐printing with Long Chain Branching Structures: Toward Desirable Crystallization Properties and Mechanical Performance