Abstract:As an eco-friendly thermoelectric material, Cu2SnSe3 has recently drawn much attention. However, its high electrical resistivity ρ and low thermopower S prohibit its thermoelectric performance. Herein, we show that a widened band gap and the increased density of states are achieved via S alloying, resulting in 1.6 times enhancement of S (from 170 to 277 μV/K). Moreover, doping In at the Sn site can cause a 19-fold decrease of ρ and a 2.2 times enhancement of S (at room temperature) due to both multivalence bands' participation in electrical transport and the further enhancement of the density of states effective mass, which allows a sharp increase in the power factor. As a result, PF = 9.3 μW cm–1 K–2 was achieved at ∼800 K for the Cu2Sn0.82In0.18Se2.7S0.3 sample. Besides, as large as 44% reduction of lattice thermal conductivity is obtained via intensified phonon scattering by In-doping-induced formation of multidimensional defects, such as Sn vacancies, dislocations, twin boundaries, and CuInSe2 nanoprecipitates. Consequently, a record high figure of merit of ZT = 1.51 at 858 K is acquired for Cu2Sn0.82In0.18Se2.7S0.3, which is 4.7-fold larger than that of pristine Cu2SnSe3.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsnano.1c03120?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsnano.1c03120</a>.Temperature dependence of Cp for Cu2SnSe3, Cu2SnSe2.7S0.3, and Cu2Sn0.82In0.18Se2.7S0.3; phase characterization for all investigated samples; temperature dependence of the ZT value for Cu2SnSe3–xSx and the repeatability of thermoelectric performance for Cu2Sn0.82In0.18Se2.7S0.3; calculation details of md*; optical band gaps for S-alloyed Cu2SnSe3; unfolded effective band structure of Cu2SnSe3; calculation of lattice thermal conductivity via the Debye–Callaway model; and the calculation details of thermopower-dependent thermoelectric properties (<a class="ext-link" href="/doi/suppl/10.1021/acsnano.1c03120/suppl_file/nn1c03120_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

High Thermoelectric Performance in P‐type Polycrystalline Cd‐doped SnSe Achieved by a Combination of Cation Vacancies and Localized Lattice Engineering

Realizing high doping efficiency and thermoelectric performance in n-type SnSe polycrystals via bandgap engineering and vacancy compensation

Achieving High Thermoelectric Figure of Merit in Polycrystalline SnSe Via Introducing Sn Vacancies

Robustly Boosting Thermoelectric Performance of N‐Type PbSe via Lattice Plainification and Dynamic Doping

High thermoelectric properties realized in polycrystalline (Ag, Ga) Co-doped SnSe via two-steps point defects modulation

High thermoelectric properties in polycrystalline SnSe materials realized by rare earth halide Co-doping

High thermoelectric performance of p-type SnTe via a synergistic band engineering and nanostructuring approach

Realizing High Thermoelectric Performance in p-Type SnSe Crystals via Convergence of Multiple Electronic Valence Bands

Realizing high thermoelectric properties in p-type polycrystalline SnSe by inducing DOS distortion

Introducing PbSe quantum dots and manipulating lattice strain contributing to high thermoelectric performance in polycrystalline SnSe

Polycrystalline SnSe–Sn1–vS Solid Solutions: Vacancy Engineering and Nanostructuring Leading to High Thermoelectric Performance

Realizing High Thermoelectric Performance of Cu and Ce Co-Doped P-Type Polycrystalline SnSe Via Inducing Nanoprecipitation Arrays

Enhanced thermoelectric performance of AgCuTe-doped polycrystalline SnSe by lattice plainification

Achieving high thermoelectric performance with Pb and Zn codoped polycrystalline SnSe via phase separation and nanostructuring strategies

Re‐Doped p‐Type Thermoelectric SnSe Polycrystals with Enhanced Power Factor and High ZT > 2

Two-dimensional WSe2/SnSe p-n junctions secure ultrahigh thermoelectric performance in n-type Pb/I Co-doped polycrystalline SnSe

Synergistic Optimization of Thermoelectric Performance in SnSe2 through co-doping: Anionic Vacancy Formation and Band Engineering

Heavy Rare Earth Element Gd Enhancing Thermoelectric Performance in p-Type Polycrystalline SnSe via Optimizing Carrier Transport and Density of States

Boosting Thermoelectric Performance of Cu 2 SnSe 3 via Comprehensive Band Structure Regulation and Intensified Phonon Scattering by Multidimensional Defects

Enhanced thermoelectric performance of n-type polycrystalline SnSe via NdCl3 doping

Contrasting Thermoelectric Properties in cubic SnSe-NaSbSe 2 and SnSe-NaSbTe 2 : High Performance Achieved via Increasing Cation Vacancies and Charge Densities