Abstract:The mixing quality of polymer melts in the mixing section of a single-screw extruder and an injection molding machine has considerable effects on the properties of the molded products. Therefore, the study of the flow field of polymer melts in the mixing section is of great importance. The lattice Boltzmann method (LBM) exhibits unique advantages in simulating non-Newtonian fluids. Many researchers have used LBM to study the flow of medium- and low-viscosity fluids. In their studies, the Reynolds number of fluid flows is generally moderate. However, polymer melts are typical high-viscosity fluids, and their flow Reynolds number is generally very small. The single-relaxation-time lattice Boltzmann method (SRT-LBM) has been used previously to study the flow field of power law fluids in the mixing section. Herein, the flow field of high-viscosity generalized Newtonian fluids in the mixing section of a single-screw extruder is studied using SRT-LBM, the two-relaxation-time lattice Boltzmann method (TRT-LBM), and the multiple-relaxation-time lattice Boltzmann method (MRT-LBM). Through comparison, TRT-LBM has been found to exhibit obvious advantages regarding stability, calculation accuracy, calculation efficiency, and selection of simulation parameters. The TRT-LBM is more suitable for studying high-viscosity generalized Newtonian fluids than SRT-LBM and MRT-LBM. SRT-LBM has low computational efficiency when simulating high-viscosity generalized Newtonian fluids, and instability is easily caused when the fluid has a yield stress. For MRT-LBM, only by studying the relaxation parameters can its advantages be fully utilized. However, optimizing the accuracy and stability of the MRT-LBM via parameter research and linear stability analysis is difficult. For non-Newtonian fluids, it is difficult to optimize the relaxation parameters to make the MRT-LBM more stable and accurate than the TRT-LBM. It is difficult for the MRT-LBM to realize its potential when simulating high-viscosity generalized Newtonian fluids. In addition, we studied the flow pattern in the cross section of the screw channel and compared it to the results reported in previous studies.

Three-dimensional isothermal simulation of PP melt flow in laminating-multiplying elements based on the finite element method

Numerical simulation of filling flow of polymer melt in injection molding

The polymer melt swelling behavior in micro-extrusion process for preparation of continuous carbon fiber reinforced PP prepreg filament

Numerical modelling of the viscoelastic polymer melt flow in material extrusion additive manufacturing

Preparation of high melt strength polypropylene by the reactive extrusion process and its foaming application

3d Finite Element Modeling Of Laser Machining Pmma

Effects of convective schemes and geometric reconstruction scheme on interface of multiple melt flows

Theoretical and Computational Analysis on the Melt Flow Behavior of Polylactic Acid in Material Extrusion Additive Manufacturing under Vibration Field

Simulation of High-Viscosity Generalized Newtonian Fluid Flows in the Mixing Section of a Screw Extruder Using the Lattice Boltzmann Model

Two-relaxation-time lattice Boltzmann model of the velocity profiles and volumetric flow rate of generalized Newtonian fluids in a single-screw extruder

ITIL: Interlaced Topologically Interlocking Lattice for continuous dual-material extrusion

Flow‐field‐assisted Shaping of Linear Low‐density Polyethylene/low‐entanglement Ultra‐high Molecular Weight Polyethylene Blends with Enhanced Mechanical Properties and Thermal Conductivity

Towards 3D Process Simulation for In Situ Hybridization of Fiber-Metal-Laminates (FML)

Numerical Simulation and Analysis of the Effect of Some Materials and Processing Parameters on the Gas Assisted Extrusion of Ultra-high Molecular Weight Polyethylene

Dimensional Analysis Theory and Molecular Dynamics Simulation of Polypropylene Melt Flow during Injection Molding Process

Numerical investigation of enhanced PCM melting performance using a thermally conductive fin in a pneumatic-based extrusion system

Polymer/LMPA for manufacturing deformable structure by coaxial printing

Finite Element Modeling of the Thermomechanical Behavior of Polyethylene

Crystal morphology and tensile properties of LLDPE containing PP fibers as obtained via dynamic packing injection molding

The effect of controlled intercalation on the mechanical performances and dimensional accuracy of material extrusion additive manufactured poly(lactic acid)/organo-montmorillonite nanocomposites

Finite Element Analysis of Scanning Speed Influence on Melted Extrusion Manufacturing