Abstract:The effect of elevated-temperature annealing in the range of 1473 K-1673 K on the coarsening kinetics of nanoparticles and microstructural evolution in an as-fabricated 12Cr-ODS steel was systematically investigated. Results show that the nanoparticles were extremely stable and continued precipitating during annealing at 1473 K, whereas, significant coarsening took place during exposure at 1673 K, increasing by 177% and 423% in diameter for 1 h and 24 h, respectively. Furthermore, heterogeneously distributed voids were developed, sizes of which increased distinctly at 1573 K and 1673 K for longer holding time. This is probably due to the growth and/or aggregation of Ar-entrapped and pre-existed voids in the as-fabricated condition. Additionally, no obvious changes were observed in microstructure and texture at 1473 K, nevertheless, full recrystallization were achieved at 1673 K for 24 h, and the major texture was not altered except reduction of the intensity. The apparent activation energy for recrystallization was experimentally calculated as 424 +/- 22 kJ/mol, which was almost the same as that for nanoparticle coarsening, i.e., 412 +/- 55 kJ/mol, suggesting that recrystallization proceeded accompanying with nanoparticle coarsening that would in turn stimulate the recrystallization process. It was deduced that recrystallization in the as-fabricated 12Cr-ODS steel was presumably not able to occur until the nanoparticles were dissolving and/or coarsening during annealing. (C) 2016 Elsevier B.V. All rights reserved.

Study on Anisotropy in Microstructure and Tensile Properties of the 12cr Oxide Dispersion Strengthened (ODS) Steel

Anisotropy in creep properties and its microstructural origins of 12Cr oxide dispersion strengthened ferrite steels

Microstructural Characterization and Strengthening Mechanisms of a 12Cr-Ods Steel

Mechanical Properties and Microstructure of 9Cr-Ods-clf-1 Steel

Effects of Fabrication Processing on the Microstructure and Mechanical Properties of Oxide Dispersion Strengthening Steels

Effect of spark plasma sintering temperature on microstructure and mechanical properties of 14Cr-ODS ferritic steels

Optimization of Microstructure and Tensile Properties for a 13Cr-1W ODS Steel Prepared by Mechanical Alloying and Spark Plasma Sintering Using Pre-Alloyed Powder

Microstructural Evolution of Two-Way Cold Rolled 12cr ODS Steel under 1073–1373 K Annealing

HIGH TEMPERATURE TENSILE TEST OF 12CR FERRITIC ODS STEEL

Hot rolling and annealing effects on the microstructure and mechanical properties of ODS austenitic steel fabricated by electron beam selective melting

Effects of Pre-Deformation on Microstructural Evolution of 12cr ODS Steel under 1473–1673 K Annealing

High-Temperature Oxidation Properties and Microstructural Evolution of Nanostructure Fe-Cr-Al ODS Alloys

Microstructural Study and Residual Stress Measurement of a Hot Rolling Work Roll Material During Isothermal Oxidation

Compressive Deformation Behavior of the Ferritic Oxide Dispersion Strengthened Alloys at Elevated Temperatures

Influence of temperature on ductility of nano-ODS steel prepared by low-energy mechanical alloying

Hot Deformation Behavior of Nanostructural Oxide Dispersion-Strengthened (ODS) Mo Alloy

Microstructure and Tensile Properties of Oxide Strengthened Ferritic Steel Fabricated Using As-Milled Powders with Dissolved Oxygen

Microstructure Evolution and Mechanical Properties of ODS FeCrAl Alloys Fabricated by an Internal Oxidation Process

Microstructural Stability of an As-Fabricated 12Cr-Ods Steel under Elevated-Temperature Annealing

Recrystallization Behavior of a Two-Way Cold Rolled 12cr ODS Steel

Characterization of Oxide Dispersoids and Mechanical Properties of 14Cr-Ods FeCrAl Alloys