Abstract:In food, chemicals and pharmaceuticals industries, the concentration is a very important parameter for quality control. Continuous process monitoring is a fundamental requirement for the process control in these industries. Besides process parameters, such as temperature, pressure, liquid level, flow rate, concentration measurement is also of special interest. More qualified information obtained from new or better sensors can significantly enhance the process quality and thereby product properties. Low-intensity ultrasonic sensor system can contribute to this development, and it has been widely used in many fields for its characteristics are non-destructive, non-invasive and rapid. In this study, a method based on ultrasound for determining the concentration of NaCl water solution with high accuracy was presented. The ultrasound velocity in different temperatures and in solutions with different concentrations was measured using an emitter-receiver method. The experimental set-up was composed of two matched piezoelectric transducers with the center frequency of around 5 MHz (one used as emitter and the other as receiver), a thermostatic tank, a CTS-80787PR pulse emitter-receiver (used to excite and receive electric signals) and a data acquisition card. The electric pulse at the emitting voltage of-25 V, the width of 100 ns and the repeated frequency of 100 Hz was sent from the CTS-80787PR to the emitter transducer and then transformed to ultrasound wave. This wave traveled through a liquid sample cell with 5 mm wide to reach the receiving transducer, and was transformed back to electric pulse signal. The signal was acquired by the CTS-80787PR and sent to a computer equipped with the LABVIEW via a 16-bit data acquisition card of PCI (peripheral component interconnect) bus with the sampling rate of 40 MS/s. A Labview interface was developed to collect signals, analyze signals, build models and validate models. Through analysis, the measurement accuracy of ultrasound velocity was 1 m/s for this equipment, which ensured the accuracy of concentration measurement. At 2.5°C gradient in the temperature range of 10-30°C, and at a gradient of 0.5 g/100 g in the concentration range of 0-10 g/100 g, NaCl water solutions were prepared. Some were regarded as calibration samples and others as validation samples. In order to predict the concentrations of NaCl water solution, a calibration model was established using a quadratic polynomial approach based on the experimental results. The coefficients of this polynomial were obtained based on ordinary multiple linear regression (OMLR) method by inserting the measurement points, analyzing the residual to eliminate abnormal sample points and checking out the regression coefficient of the model by t-test. The developed model had high prediction accuracy and stability with the maximum prediction error of 0.25 g/100 g, the determination coefficient of calibration (Rcal2) of 0.9992, the determination coefficient of validation (Rval2) of 0.9988, the root mean square error of calibration (RMSEC) of 0.0894 g/100 g, the root mean square error of prediction (RMSEP) of 0.1015 g/100 g and the ratio performance deviation (RPD) of 28.57, which indicated that the model could be used for practical detection accurately and steadily, and was helpful for on-line measuring.

An AlN Based SAW Device for Detection of Impurities in Water Based on Measuring the Signal-to-Noise Ratio

A surface acoustic wave device for water impurity levels monitoring by measuring signal-to-perturbation ratios

Study of a novel surface acoustic wave liquid detection system

A Study On Ain Film-Based Saw Attenuation In Liquids And Their Potential As Liquid Ethanol Sensors

A Novel Chemical Sensor with Multiple All-Solid-state Electrodes and Its Application in Freshwater Environmental Monitoring.

A discovery of an ultra-pure water detection method based on water mark

Oscillation-Based Active Sensor on SIW Reentrant Cavity Resonator for Self-Sustained Ultralow Concentration Detection to Saline Solution

Design and research of microfluidic chips detection instrument with high SNR

Digital phase detection approach and its application for AlN dual-mode differential surface acoustic wave sensing

Blank sample denoising algorithm (BSDA): An effective spectral noise reduction in water sample LIBS detection

Discrete Microfluidics Based on Aluminum Nitride Surface Acoustic Wave Devices

Machine learning assisted dual-functional nanophotonic sensor for organic pollutant detection and degradation in water

A Nanofluidic Sensor for Real-Time Detection of Ultratrace Contaminant Particles in IC Fabrication

Engineering Silver Nanostructures for Surface Acoustic Wave Humidity Sensors Sensitivity Enhancement

Determination of aldehydes in water samples by coupling magnetism-reinforced molecular imprinting monolith microextraction and non-aqueous capillary electrophoresis

Ultramicro Interdigitated Array Electrode Chip with Optimized Construction for Detection of Ammonia Nitrogen in Water

Research development of surface acoustic wave sensors for NO2 gas detection

A design of spectrophotometric microfluidic chip sensor for analyzing silicate in seawater

A Novel Surface Acoustic Wave Sensor Array Based on Wireless Communication Network

Direct Detection of Nitrite and Nitrate in Water on Three-Dimensional Composite Surface-Enhanced Raman Scattering Substrate

Design and test of high accurately measuring equipment for NaCl water solution utilizing ultrasonic velocity with temperature correction