Abstract:Efforts to simulate the extreme toughness of the polycrystalline diamond variety known as carbonado typically entail the sintering of diamond powders in the presence of metal solvent-catalysts. In this study, we have attempted to duplicate the carbonado microstructure by sintering diamond powders without catalysts in a multi-anvil press at pressures of 6 to 9 GPa, temperatures of 1200 to 1800 degreesC, and times up to 6 h. The resultant microstructural defect assemblages for each experimental condition were characterized by transmission electron microscopy (TEM). Despite the absence of catalysts, sintered compacts were successfully produced for all runs, though intergranular porosity was significantly higher than that observed in natural carbonado. Primary grain sizes were reduced by more than 50% from their original dimensions in some experiments due to surface fracturing and abrasion, and aperiodic slip planes rigorously parallel to {111} consistently emerged in high densities, with lamellar spacings of 3 to 30 nm. In addition, sintering over all conditions produced polysynthetic spinel twinning in close association with the partial slip defects.Compacts compressed at 8 GPa produced some euhedral crystals with very low dislocation densities surrounded by grains in which dislocation densities were quite high. In addition, curviplanar defects loosely constrained to {111} were visible within some specimens sintered at the highest pressures. These textures resembled the polygonalization fabrics and defect microstructures observed in natural carbonado (De et al. 1998), and the appearance of these features suggests that our experiments at their most extreme pressure and temperature parameters reproduced carbonado-like defect assemblages. The formation of such textures in quasi-hydrostatic experiments suggests that shock metamorphism is not required to produce the periodic defect lamellae observed in carbonado.

Synthesis of Nanopolycrystalline Mesoporous Diamond from Periodic Mesoporous Carbon: Mesoporosity Increases with Increasing Synthesis Pressure

Synthesis of Nano-Polycrystalline Diamond under High Pressure and High Temperature

Nano-polycrystalline diamond formation under ultra-high pressure

Catalyst-Free Synthesis Of Transparent, Mesoporous Diamond Monoliths From Periodic Mesoporous Carbon Cmk-8

Synthesizing bulk polycrystalline diamond by method of direct phase transition

Facile Diamond Synthesis from Lower Diamondoids

Shear driven formation of nano-diamonds at sub-gigapascals and 300 K

Nano-Diamond Compressibility at Pressures Up to 85 GPa

Graphitization of Diamond Powders of Different Sizes at High Pressure–high Temperature

Effect of pressure on sintering behavior of polycrystalline diamond

Effect of pressure on nanocrystalline diamond films deposition by hot filament CVD technique from CH4/H2 gas mixture

Microstructural Study of Synthetic Sintered Diamond and Comparison with Carbonado, A Natural Polycrystalline Diamond

Synthesis and Mechanism Study of Carbon Nanowires, Carbon Nanotubes, and Carbon Pompons on Single-Crystal Diamonds

Effect of pressure on large size diamond single crystal synthesized by temperature gradient method under low nitrogen condition

Shear-promoted Graphite-to-diamond Phase Transition at the Grain Boundary of Nanocrystalline Graphite

Highly Boron-Doped Graphite and Diamond Synthesized From Adamantane and Ortho-Carborane under High Pressure

On the High-Pressure Behavior of Periodic Mesoscale SBA-16 Silica/carbon Composites: Studies at 10 GPa Between 25 and 1800 °C

Micron Diamond Composites with Nanocrystalline Silicon Carbide Bonding

Title: Periodic Mesoporous Hexagonal Boron Nitride at High Pressure: A Route to Cubic Boron Nitride Nanocrystals and Mesoporous Cubic Boron Nitride

Theoretical Study on Phase Transition of Various Graphitic Structures under High Pressure

Rapid Growth of Nanocrystalline Diamond on Single Crystal Diamond for Studies on Materials under Extreme Conditions