Abstract:Defect engineering is a promising method for improving light harvesting in photocatalytic materials like Zinc sulphide (ZnS). By altering the S/Zn molar ratio during hydrothermal processes, Zn and S defects are successfully introduced into the ZnS crystal. The band structures can be modified by adding defects to the crystal structure of ZnS samples. During the treatment process, defects are formed on the surface. XRD and Raman studies are used for the confirmation of the crystallinity and phase formation of the samples. Using an X-ray peak pattern assessment based on the Debye Scherer model, the Williamson-Hall model, and the size strain plot, it was possible to study the influence of crystal defect on the structural characteristics of ZnS nanoparticles. The band gap (E g ) values were estimated using UV–Vis diffuse spectroscopy (UV–Vis DRS) and found that the E g is reduced from 3.28 to 3.49 eV by altering the S/Zn molar ratio. Photoluminescence study (PL) shows these ZnS nanoparticles emit violet and blue radiations. In keeping with the results of XRD, TEM demonstrated the nanoscale of the prepared samples and exhibited a small agglomeration of homogenous nanoparticles. Scanning electron microscopy (SEM) was used to examine the surface morphology of the ZnS particles. Inductively Coupled Plasma Optical Emission Spectroscopy ( ICP-OES) and X-ray photoelectron spectroscopy (XPS) were used to evaluate and validate the elemental composition. XPS results indicate the presence of defects on the prepared ZnS nanoparticles. For the investigation of vacancy-dependent catalytic activity under exposure to visible light, defective ZnS with different quantities of Zn and S voids are used as catalysts. The lowest S/Zn sample, ZnS0.67 and the highest S/Zn sample, ZnS3, show superior photocatalytic activity.

Optimizing electrospinning-hydrothermal hybrid process based on Taguchi method for modulation of point defects in ZnO micro/nano arrays towards photoelectronic application

Surface Morphology, Electrochemical and Electrical Performances of ZnO Thin Films Sensitized with Ag Nanoparticles by UV Irradiation

Pulsed-laser Treatment for Lowering Resistance and Enhancing Field Emission of Solution-Grown ZnO Nanowires

Controllable Heterogeneous Nucleation for Patterning High‐Quality Vertical and Horizontal ZnO Microstructures toward Photodetectors

Concurrent Improvement of Photocarrier Separation and Extraction in ZnO Nanocrystal Ultraviolet Photodetectors

Hydrothermal Synthesis of Well-Aligned ZnO Nanorod Arrays on Silicon

Probing size-dependent defects in zinc oxide using synchrotron techniques: impact on photocatalytic efficiency

Identification of Defect-Related Emissions in ZnO Hybrid Materials

High Speed Shearing: A Novel Approach for High-Quality ZnO Nanoparticle Synthesis and Photocatalytic Activity Control

ZnO Defect Modulation for Efficient Photocatalysis

Tunable Hydrogen-Related Defects in ZnO Nanowires Using Oxygen Plasma Treatment by Ion Energy Adjustment

Defect-Related Photoluminescence and Photocatalytic Properties of Porous Zno Nanosheets

Effect of Growth Time and Annealing on the Structural Defect Concentration of Hydrothermally Grown Zno Nanowires

Defect Engineering through Field-Effect-Induced Sensitization of Surface-Confined Grain Coalescence: A Route to Enhanced Electron Mobility in Li-Doped ZnO

Field-assisted growth of one-dimensional ZnO nanostructures with high defect density

Tuning defects in oxides at room temperature by lithium reduction

Towards Low Temperature Processed ZnO Dye-Sensitized Solar Cells

Tailoring ZnO Spontaneous Emission with Plasmonic Radiative Local Density of States Using Cathodoluminescence Microscopy

Defect engineering for enhanced optical and photocatalytic properties of ZnS nanoparticles synthesized by hydrothermal method

Advances in ZnO: Manipulation of defects for enhancing their technological potentials

Hydrothermal Synthesis of ZnO Nanoflowers: Exploring the Relationship between Morphology, Defects, and Photocatalytic Activity