Abstract:The emerging photovoltaic technology, namely perovskite photovoltaics, follows a style to the blooming flower with superficial prosperity described by the ancient poet Yuxi Liu. Metal-halide perovskite has become one of the most promising photovoltaic materials for thin-film solar-cell applications, mainly due to its exellent visible light capture capability, large diffusion coefficients and long diffusion lengths of charge carriers (both electrons and holes). The reported power conversion efficiency of laboratory produced perovskite solar cells (PSCs) has exceeded 25%. However, this value was only achieved for devices of less than 0.1 cm(2)dimensions, and decreases significantly with the increase in area (for example, down to 11.6% for a device area of similar to 800 cm(2), showing the issues with the scalability). In PSCs, the electron transport layer (ETL) has to perform two essential functions, which are related: (i) to collect and transfer charges after the injection of electrons from the perovskite light harvester; and (ii) to block the backflow of holes, thus realizing effective charge separation and suppressing charge carrier recombination. However, there are several critical issues associated with the ETLs which limit the further development of the PSCs. For example, the experimentally obtained open-circuit voltages in PSCs are typically much lower compared to the theoretical voltage limit with their optical bandgaps between 1.59 and 1.63 eV. This is mainly attributed to inefficient charge transport in the PSCs due to inhomogeneous charge accumulation and serious interfacial recombination at the interfaces between the ETL and the perovskite active layer. We scan recent developments of ETLs in PSCs, and discuss design methodologies, mechanisms, processing and characterization of new types of ETLs. High power conversion efficiency with large open-circuit voltages/photo-currents could be achieved through designing materials and microstructures for high-quality ETLs with a high electron mobility, high electrical conductivity and pinhole-free film morphology. It is crucial to balance the charge diffusion processes in the respective charge collective layers of PSCs as the interfaces between the ETLs and perovskites along with their interfacial structures play key roles in achieving new solid-state mesoscopic solar cells optimized open circuit voltages and output photocurrents.

PbTiO3 As Electron‐Selective Layer for High‐Efficiency Perovskite Solar Cells: Enhanced Electron Extraction Via Tunable Ferroelectric Polarization

TiO2 Electron Transport Layer with P–n Homojunctions for Efficient and Stable Perovskite Solar Cells

Rational Design of Solution-Processed Ti-Fe-O Ternary Oxides for Efficient Planar CH3NH3PbI3 Perovskite Solar Cells with Suppressed Hysteresis

Efficient rare earth co-doped TiO2 electron transport layer for high-performance perovskite solar cells.

Round-comb Fe2O3@SnO2 Heterostructures Enable Efficient Light Harvesting and Charge Extraction for High-Performance All-Inorganic Perovskite Solar Cells.

Alleviating Interfacial Recombination of Heterojunction Electron Transport Layer via Oxygen Vacancy Engineering for Efficient Perovskite Solar Cells over 23%

CsPbBr3 Quantum Dots‐Sensitized Mesoporous TiO2 Electron Transport Layers for High‐Efficiency Perovskite Solar Cells

Laser Derived Electron Transport Layers with Embedded p‐n Heterointerfaces Enabling Planar Perovskite Solar Cells with Efficiency over 25%

An Energy Level Alignment Strategy to Boost the Open-Circuit Voltage Via a Mg:TiO2 Compact Layer in the Planar Heterojunction CsPbBr3 Solar Cells

An energy level alignment strategy to boost the open-circuit voltage via a Mg:TiO<sub>2</sub> compact layer in the planar heterojunction CsPbBr<sub>3</sub> solar cells

A low-temperature TiO2/SnO2 electron transport layer for high-performance planar perovskite solar cells

Enhanced Carrier Separation Efficiency and Performance in Planar-Structure Perovskite Solar Cells Through an Interfacial Modifying Layer of Ultrathin Mesoporous TiO2

Efficient Planar Perovskite Solar Cells with Low-Temperature Atomic Layer Deposited TiO2 Electron Transport Layer and Interfacial Modifier

An Ultrathin Ferroelectric Perovskite Oxide Layer For High-Performance Hole Transport Material Free Carbon Based Halide Perovskite Solar Cells

Advances in design engineering and merits of electron transporting layers in perovskite solar cells

Modulation of the Interfacial Contact Via Self-Assembled Molecule Interlayer Towards Highly Efficient and Stable Poly(3-Hexylthiophene)-based Perovskite Solar Cells

Interface Modification for Energy Levels Alignment and Charge Extraction in CsPbI$_3$ Perovskite Solar Cells

Enhanced Electric Field Minimizing Quasi‐Fermi Level Splitting Deficit for High‐Performance Tin‐Lead Perovskite Solar Cells

Interface Engineering for Efficient ETL-free Perovskite Solar Cells Via Self-Assembled Bifunctional Monolayer

TiO2/SnO2 Electron Transport Double Layers with Ultrathin SnO2 for Efficient Planar Perovskite Solar Cells