Abstract:Inorganic CsPbIBr2 perovskite has been considered as a promising light-absorbing material for solar cells due to its high stability and suitable bandgap. Although the remarkable improvement of CsPbIBr2 PSC has been achieved, the efficiency of this cell is still lower than those of other analogues and far below its theoretical limit. This is mainly due to the serious charge recombination in the as-fabricated CsPbIBr2 cells derived from the poor-quality CsPbIBr2 perovskite film with a large quantity of defects and numerous grain boundaries. Therefore, fabricating high-quality CsPbIBr2 perovskite film is a key factor for the further efficiency improvement of CsPbIBr2 PSCs. Herein, phenylthiourea (PTU) additive is introduced into the CsPbIBr2 precursor to tailor the crystallization of CsPbIBr2 perovskite for fabricating high-quality CsPbIBr2 perovskite. The C=S group of PTU can coordinate with PbBr2 in the precursor owing to the lone-pair electrons on S and the empty orbits of Pb2+. The strong interaction between PTU and the CsPbIBr2 precursor components can form PTU·Pb···Br(I) intermediate phase in the precursor upon PTU introduction. The PTU·Pb···Br(I) intermediate phase can reduce the nucleation rate of perovskite and modulate the perovskite crystal growth because the extra energy is required to break the strong coordination bond in the intermediate phase, resulting in a low crystallization rate of CsPbIBr2 perovskite. Such a retardation of perovskite crystallization is conducive to the formation of high-crystallinity perovskite film with smooth surface, large crystal grains, high crystallization, and low density of defect. Meanwhile, the decomposition of PTU during thermal annealing makes the S2– inserted into interstitial of CsPbIBr2 crystal lattice, which greatly enhance the stability of CsPbIBr2 perovskite. The carbon-based PSCs with a normal n-i-p structure of FTO/compact-TiO2 layer/meso-TiO2 layer/perovskite film/carbon layer are fabricated, and their photovoltaic performances are measured under a simulated AM1.5 illumination (100 mW·cm–2). The PSC based on PTU-CsPbIBr2 perovskite delivers a high power conversion efficiency of 10.09%, which is much higher than that of the control device. This great improvement of photovoltaic performance can be attributed to the largely promoted perovskite quality, which enhances the charge collection and suppresses the charge recombination in the device. In addition, the unencapsulated device preserves 82% of the initial efficiency after being stored under ambient condition for 35 days, suggesting excellent stability. Therefore, this work provides an effective complementary strategy for effectively improving the performance of inorganic PSCs.

CsPbBr3 Quantum Dots‐Sensitized Mesoporous TiO2 Electron Transport Layers for High‐Efficiency Perovskite Solar Cells

CH 3 NH 3 PbBr 3– x I x Quantum Dots Enhance Bulk Crystallization and Interface Charge Transfer for Efficient and Stable Perovskite Solar Cells

Ch3nh3pbbr3-Xix Quantum Dots Enhance Bulk Crystallization And Interface Charge Transfer For Efficient And Stable Perovskite Solar Cells

Performance Enhancement of Hole Transport Layer-Free Carbon-Based CsPbIBr2 Solar Cells through the Application of Perovskite Quantum Dots

Multistrategy Toward Highly Efficient and Stable CsPbI2Br Perovskite Solar Cells Based on Dopant‐Free Poly(3‐Hexylthiophene)

TiO2 Electron Transport Layer with P–n Homojunctions for Efficient and Stable Perovskite Solar Cells

Multistrategy Toward Highly Efficient and Stable CsPbI 2 Br Perovskite Solar Cells Based on Dopant‐Free Poly(3‐Hexylthiophene)

CH<sub>3</sub>NH<sub>3</sub>PbBr<sub>3–<i>x</i></sub>I<sub><i>x</i></sub> Quantum Dots Enhance Bulk Crystallization and Interface Charge Transfer for Efficient and Stable Perovskite Solar Cells

Efficient and Stable Perovskite Solar Cells Through E-Beam Preparation of Cerium Doped TiO2 Electron Transport Layer, Ultraviolet Conversion Layer CsPbBr3 and the Encapsulation Layer Al2O3

A Novel Conductive Mesoporous Layer with a Dynamic Two-Step Deposition Strategy Boosts Efficiency of Perovskite Solar Cells to 20%

Single Source, Surfactant‐Free, and One‐Step Solvothermal Route Synthesized TiO 2 Microspheres for Highly Efficient Mesoscopic Perovskite Solar Cells

Poly(3-hexylthiophene)/zinc phthalocyanine composites for advanced interface engineering of 10.03%-efficiency CsPbBr3 perovskite solar cells

Boosting the Efficiency of Carbon-Based Planar CsPbBr3 Perovskite Solar Cells by a Modified Multistep Spin-Coating Technique and Interface Engineering

Efficiency and stability enhancement of perovskite solar cells by introducing CsPbI3 quantum dots as an interface engineering layer

High-Efficiency All-Inorganic Perovskite Solar Cells Tailored by Scalable Rutile TiO 2 Nanorod Arrays with Excellent Stability

Tailoring of CsPbIBr2 Perovskite Crystallization Via Phenylthiourea for Stable and Efficiency Perovskite Solar Cells

Passivation Effect of CsPbI<sub>3</sub> Quantum Dots on the Performance and Stability of Perovskite Solar Cells

In Situ Combined‐Hole Transport Layer for Highly Efficient Perovskite Solar Cells

Efficient rare earth co-doped TiO2 electron transport layer for high-performance perovskite solar cells.

Dual Strategy Based on Quantum Dot Doping and Phenylethylamine Iodide Surface Modification for High-Performance and Stable Perovskite Solar Cells

One‐Step Construction of a Perovskite/TiO2 Heterojunction toward Highly Stable Inverted All‐Layer‐Inorganic CsPbI2Br Perovskite Solar Cells with 17.1% Efficiency