Abstract:Surface modification of carbon fiber with 1,1-dihydroperoxycyclohexane (DHPC) before application of SiO 2 barrier coating was studied. IR spectroscopy showed presence of the COOH carboxyl groups on the surface of modified carbon fibers. The modified surface has less hydrophobicity due to the presence of polar groups, which contribute to a change in the wettability of the fiber by the sol–gel solution and the adhesion of the oxide coating to the fiber surface. The quality and thickness of the oxide coatings were assessed by scanning electron microscopy. The use of DHPC leads to oxidation of the carbon fiber, making surface longitudinal stripes deeper. To determine the effect of DHPC modification on the properties of the fiber surface, a SiO 2 coating was applied by immersion in a tetraethoxysilane sol. DHPC modification leads to the formation of a uniform SiO 2 coating on the fiber surface. After the heat treatment, the coating thickness on the DHPC–modified fibers is 130 ± 30 nm. Analysis of the IR spectra showed that the addition of DHPC to the sol leads to an increase in the intensity of the Si–O–Si, Si–OH, and OH absorption bands, which are characteristic of the hydrolysis and polycondensation products of tetraethoxysilane. In the wavenumber range of 400–1200 cm –1 , the Si–O–Si fragments form, which is confirmed by the presence of bands of Si–O– deformation bond at ν = 881 and 442 cm –1 . The introduction of DHPC into the sol promotes the formation of a uniform coating on the carbon fibers. The coating thickness on the initial fibers reaches 410±100 nm at room temperature, decreasing to 190±60 nm after heating. The fiber and sol modification contribute to formation of a uniform coating with a thickness of 200 ± 70 nm and 130 ± 30 nm before and after the heating, respectively. DHPC modification of the fiber surface and tetraethoxysilane sol promotes the formation of continuous, uniform, and quality SiO 2 coatings on the surface of carbon fibers.

Surface Modification of Kevlar Fiber by Nanosio2 Deposition in Supercritical Fluid

Effect of grafting alkoxysilane on the surface properties of kevlar fiber

Mechanical Properties of Carbon Fiber Composites Modified with Nano-Sio2 in the Interphase

Surface modification of Kevlar fibre fabric and its influence on the properties of Kevlar/epoxy composites

Influence of Carbon Nanotube Coatings on Carbon Fiber by Ultrasonically Assisted Electrophoretic Deposition on Its Composite Interfacial Property.

Modification of carbon nanotubes using poly(vinylidene fluoride) with assistance of supercritical carbon dioxide: the impact of solvent

Study on Surface Properties of Aramid Fiber Modified in Supercritical Carbon Dioxide by Glycidyl-POSS

Interfacial Enhancement of Fibrillar Silicates (fss)/epdm Nanocomposites by Surface Modification of FS in Supercritical CO2

Interfacial Improvement of Carbon Fiber/epoxy Composites Using a Simple Process for Depositing Commercially Functionalized Carbon Nanotubes on the Fibers

Carbon Fiber Surface Nano-Modification and Enhanced Mechanical Properties of Fiber Reinforced Cementitious Composites

Growing Nano-SiO2 on the Surface of Aramid Fibers Assisted by Supercritical CO2 to Enhance the Thermal Stability, Interfacial Shear Strength, and UV Resistance

The Modification of Kevlar Fibers in Coupling Agents by Γ -Ray Co-Irradiation

Surface Modification of Carbon Fibers by Microwave Etching for Epoxy Resin Composite

Surface Treatment and Dipping Procrss of Kevlar Fiber

Recent advancement in surface modification of aramid fiber assisted by supercritical carbon dioxide

High Efficient and Continuous Surface Modification of Carbon Fibers with Improved Tensile Strength and Interfacial Adhesion

Effect of Surface Modification of Carbon Fibers on the Formation of SiO2 Coatings

Effect of Surface Treatment on the Mechanical and Tribological Performance of Kevlar Pulp Reinforced Epoxy Composites

Influence of Fibre Surface Oxidation–reduction Followed by Silsesquioxane Coating Treatment on Interfacial Mechanical Properties of Carbon Fibre/polyarylacetylene Composites

Two-step surface treatment of 3D braided carbon/Kevlar hybrid fabric and influence on mechanical performance of its composites

Enhanced Thermal Properties of Epoxy Resin Composites: The role of Tailoring Surface Chemistry of Nano-SiO<sub>2</sub>