Abstract:Solid oxide fuel cell (SOFC) is an energy conversion device that converts chemical energy in fuels into electric energy directly with the advantages of high efficient, clean, and wide fuel adaptability. Most hydrocarbons such as natural gas, ethane and bio-oil can be used as fuels in SOFC. When a hydrocarbon fuel, such as methane (CH4), is directly used for IT-SOFCs without prereforming by adding oxygen, steam or carbon dioxide, it is electrochemically oxidized on the triple-phase boundaries (TPB) with a strong tendency of carbon deposition in the traditional Ni-based anode. In this paper, we introduce an extra internal reforming layer on the surface of anode-support. The layer of a LaCrO3 based perovskite with exsolved Ni nanoparticles catalyst (La0.6Sr0.2Cr0.85Ni0.15O3 showed high stability in reducing atmosphere and excellent catalytic performance. Based on this, two types of anode-supported cell are fabricated by tape casting, screen printing and sintering processes. The first one is a conventional anode supported cell with a configuration of Ni-GDC/GDC/GDC-LSCF (cell 1); and the other contains a reforming layer mixed with La0.6Sr0.2Cr0.85Ni0.15O3 and SDC which was a well coking resistant promoters (cell 2). When CH4–CO2 was used as the fuel, which was supposed to yield syngas with the H2–CO ratio close to unity, the polarization resistance of the cell 1 reach at 0.247 Ω cm2 whereas the value of cell 2 is 0.082Ω cm2 at 750 °C. These results implied that both the physical and the chemical properties of the TPB have been altered drastically during internal dry reforming since that Ni-based anode show poor catalytic performance in reforming and are prone to coking. Consequently, the maximum power density for cell 1 was 470 mW cm-2 and the cell suffered from degradations during a 1 h galvanostatic operation at 1 A cm-2. The performances of the cell 2 are significantly increased above the level of the cell 1, demonstrating a peak power density at 929 mW cm-2 at 750 °C and a stable cell voltage at 1 A cm-2 and 750 °C for 48 h. Carbon deposition in the anode region of the tested cell 2 is not detected, as the La0.6Sr0.2Cr0.85Ni0.15O3 is a more active and stable catalyst than the Ni-based anode-support for dry reforming. Finally we demonstrated the strong interaction between the exsolved nanoparticles and the substrate could prevent coking deposition and proposed a promising configuration of double-layer anode for solid oxide fuel cells with on-cell reforming. Figure 1

Coking-resistant Ce0.8Ni0.2O2-δ Internal Reforming Layer for Direct Methane Solid Oxide Fuel Cells

Proton-Conducting La-Doped Ceria-Based Internal Reforming Layer for Direct Methane Solid Oxide Fuel Cells

Study on a Novel Double-Layer Anode for Solid Oxide Fuel Cells Based on CO2 Dry Reforming of Methane

Surface Tuned La 0.9 Ca 0.1 Fe 0.9 Nb 0.1 O 3-Δ Based Anode for Direct Methane Solid Oxide Fuel Cells by Infiltration Method

Direct-Methane Solid Oxide Fuel Cells with Hierarchically Porous Ni-Based Anode Deposited with Nanocatalyst Layer

Ceria coated Ni as anodes for direct utilization of methane in low-temperature solid oxide fuel cells

A Robust NiO–Sm0.2Ce0.8O1.9 Anode for Direct-Methane Solid Oxide Fuel Cell

A Highly Coking-Resistant Solid Oxide Fuel Cell with a Nickel Doped Ceria: Ce1−xNixO2−y Reformation Layer

Enhanced coking resistance of a Ni cermet anode by a chromates protective layer

Enhanced electrochemical performance and durability for direct CH4–CO2 solid oxide fuel cells with an on-cell reforming layer

Infiltrated Ni0.08Co0.02Ce0.02CeO2-x@Ni0.8Co0.2 Catalysts for a Finger-Like Anode in Direct Methane-Fueled Solid Oxide Fuel Cells

Enhanced Coking Resistance of Ni Cermet Anodes for Solid Oxide Fuel Cells Based on Methane On‐cell Reforming by a Redox‐stable Double‐perovskite Sr 2 MoFeO 6‐Δ

Direct carbon dioxide-methane solid oxide fuel cells integrated for high-efficiency power generation with La0.75Sr0.25Cr0.5Fe0.4Ni0.1O3–δ-based dry reforming catalyst

Sm0.2(Ce1−xTix)0.8O1.9 Modified Ni–yttria-stabilized Zirconia Anode for Direct Methane Fuel Cell

Novel In-Situ MgO Nano-Layer Decorated Carbon-Tolerant Anode for Solid Oxide Fuel Cells

A direct-methane solid oxide fuel cell with a functionally engineered Ni–Fe metal support

Performance of Ni/Scsz Cermet Anode Modified by Coating with Gd0.2ce0.8o2 for an Sofc Running on Methane Fuel

Anode Catalyst Layers for Direct Hydrocarbon and Internal Reforming SOFCs

La0.6Sr0.4Co0.2Fe0.8O3-δ Nanoparticles Modified Ni-based Anode for Direct Methane-Fueled SOFCs

Direct-methane Solid Oxide Fuel Cells with an in Situ Formed Ni–Fe Alloy Composite Catalyst Layer over Ni–YSZ Anodes

A Hierarchical Porous Microstructure for Improving Long-Term Stability of Ni1-Xcux/Sdc Anode-Supported It-Sofcs Fueled with Dry Methane