Abstract:In order to predict flow behavior and find the optimum hot working processing parameters for 5754 aluminum alloy, the experimental flow stress data obtained from the isothermal hot compression tests on a Gleeble-3500 thermo-simulation apparatus, with different strain rates (0.1⁻10 s⁻1) and temperatures (300⁻500 &deg;C), were used to construct the constitutive models of the strain-compensation Arrhenius (SA) and back propagation (BP) artificial neural network (ANN). In addition, an optimized BP⁻ANN model based on the genetic algorithm (GA) was established. Furthermore, the predictability of the three models was evaluated by the statistical indicators, including the correlation coefficient (R) and average absolute relative error (AARE). The results showed that the R of the SA model, BP⁻ANN model, and ANN⁻GA model were 0.9918, 0.9929, and 0.9999, respectively, while the AARE of these models was found to be 3.2499⁻5.6774%, 0.0567⁻5.4436% and 0.0232⁻1.0485%, respectively. The prediction error of the SA model was high at 400 &deg;C. It was more accurate to use the BP⁻ANN model to determine the flow behavior compared to the SA model. However, the BP⁻ANN model had more instability at 300 &deg;C and a true strain in the range of 0.4⁻0.6. When compared with the SA model and BP⁻ANN model, the ANN⁻GA model had a more efficient and more accurate prediction ability during the whole deformation process. Furthermore, the dynamic softening characteristic was analyzed by the flow curves. All curves showed that 5754 aluminum alloy showed the typical rheological characteristics. The flow stress rose rapidly with increasing strain until it reached a peak. After this, the flow stress remained constant, which demonstrates a steady flow softening phenomenon. Besides, the flow stress and the required variables to reach the steady state deformation increased with increasing strain rate and decreasing temperature.

Prediction on Hot Deformation Behavior of Spray Formed Ultra-High Strength Aluminum Alloy-a Comparative Study Using Constitutive Models

Prediction on Hot Deformation Behavior of Spray-Formed 7055 Aluminum Alloy Via Phenomenological Models

Prediction and Evaluation of Hot Deformation Properties of Aluminum Matrix Composites Reinforced with Spray-Formed Ceramic Particles

Investigation of Constitutive Model of As-Extruded Spray-Forming 7055 Aluminum Alloy Based on BP Artificial Neural Network

Artificial neural network prediction to the hot compressive deformation behavior of Al–Cu–Mg–Ag heat-resistant aluminum alloy

Constitutive Modeling of the Hot Deformation Behavior in 6082 Aluminum Alloy

Research on constitutive model of aluminum alloy 7075 thermal deformation based on deep neural network

Dynamic Behavior and Modified Artificial Neural Network Model for Predicting Flow Stress During Hot Deformation of Alloy 925

Hot Deformation Flow Behaviour Modelling of Cast-Extruded Al 7075 Alloy Using Arrhenius Equations and Artificial Neural Network

Prediction of Flow Stress of Annealed 7075 Al Alloy in Hot Deformation Using Strain-Compensated Arrhenius and Neural Network Models

Modeling the Hot Deformation Behaviors of As-Extruded 7075 Aluminum Alloy by an Artificial Neural Network with Back-Propagation Algorithm

An Improved Constitutive Model Based on BP Artificial Neural Network and 3D Processing Maps of a Spray-Formed Al–Cu–Li Alloy

Modeling of Flow Stress of As-Rolled 7075 Aluminum Alloy during Hot Deformation by Artificial Neural Network and Application

Application of Constitutive Models and Machine Learning Models to Predict the Elevated Temperature Flow Behavior of TiAl Alloy

A Physically-Based Constitutive Modelling of a High Strength Aluminum Alloy at Hot Working Conditions

Flow Behavior of Al–6.2Zn–0.70Mg–0.30Mn–0.17Zr Alloy During Hot Compressive Deformation Based on Arrhenius and ANN Models

Constitutive Model of As-cast 7050 Aluminum Alloy at Large Region Strain Rate with Extrapolated Ability

Artificial Neural Network for Predicting the Flow Behaviors of Hot Compressed 2124-T851 Aluminum Alloy

Artificial Neural Network Modeling to Evaluate the Dynamic Flow Stress of 7050 Aluminum Alloy

A Modified Back Propagation Artificial Neural Network Model Based on Genetic Algorithm to Predict the Flow Behavior of 5754 Aluminum Alloy

Hot Deformation Behavior and Constitutive Modeling of High Strength Low-Carbon Alloyed Steel Manufactured by Wire and Arc Additive Manufacturing