Abstract:To further clarify the effect mechanism of MoS 2 element diffusion on tribological properties of cemented carbide materials, an investigation was carried in this study. The diffusion process between cemented carbide inserts and MoS 2 powder under high temperature condition was carried out in a muffle furnace device. The surface morphology and chemical element content of test samples were observed and measured with scanning electron microscope, energy spectrum, and X-ray diffraction instruments. The kinetics of the diffusion process was quantitatively discussed by thermodynamic experiments. Tribological experiments were carried out using friction and wear machine with which the friction coefficient and wear scar were obtained. The experimental results show that high temperature has a significant effect on physical and mechanical properties of cemented carbide materials. Moreover, MoS 2 elements diffusion on sample surface is existed and induced by thermal action, which results in a further changing of material properties of cemented carbide. The WC grain growth is inhibited when molybdenum element is only infiltration on sample surface at 500 °C, which improves the surface morphology and hardness of test sample. However, the oxidation rate, friction coefficient, and wear rate of test sample are the highest when heating temperature larger than 500 °C. The main reason is that, as the temperature increasing, the diffusion of sulfur elements is occurred and intensified the loss of cobalt element on sample surface. So, the bonding ability of it is decreased due to the loss of bonding phase Co. Thus, the surface hardness and wear resistance of test sample is deteriorated. This study provides a theoretical foundation for the application of molybdenum disulfide in tool cutting lubrication condition.

Tribological Behavior and Wear Mechanism of Pure WC at Wide Range Temperature from 25 to 800 °C in Vacuum and Air Environment

Enhancing High-Temperature Wear Resistance by Constructing the Amorphous-Crystal Heterointerface Structure in WO3/TiO2 Composite Coatings

Wear Behaviour and Microstructural Changes of SiCw-Al Composite under Unlubricated Sliding Friction

Mechanical and tribological performance of (TiNbTaWMo)C high-entropy ceramics in a wide temperature range

Wear Mechanism and Evolution of Tribofilm of Ceramic on Steel Pairs under Ester Oil Lubrication in Wide Temperature Range

High temperature fracture mechanism of ultrafine WC-Co cemented carbides containing (Ti,W)C

Effect of different working conditions on tribological behaviors of PcBN/440c stainless steel in vacuum environment

Tribological properties and wear resistance mechanism of WC-ZrO2-Al2O3 ceramics

Tribological behavior of a novel Si- and WC- co-reinforced a-C multilayer coating at 25– 500 °C

Tribological Performance and Wear Mechanism of Laser Cladded NiCrAl-WC Coatings at High-Temperature

Influences of different temperatures on the mechanical properties and wear resistance against Ti6Al4V of Ti doped diamond-like carbon deposited on cemented carbide

Effect of Temperature on Wear Behavior in a Ti-V-Cr Base Fireproof Titanium Alloy

Wear Evolution of the Glass Fiber-Reinforced PTFE under Dry Sliding and Elevated Temperature

Effect of MoS 2 element diffusion under high temperature condition on the tribological properties of cemented carbide materials

Effect of tungsten carbide content on the tribological behavior of TiB2–TiC-based cermets

Effects of WC mass fraction on microstructure and tribological behavior of plasma sprayed FeMnCoCr–WC coatings

Effects of Temperature on the Tribological Properties of NM600 under Sliding Wear

Microstructure and tribological properties of laser cladded TiC reinforced WC-10Co4Cr coatings at 500 °C

High temperature tribological behavior of atmospheric plasma-sprayed CoCrFeNiW0.3 + 5 at% C high-entropy alloy coating

High temperature and room temperature tribological behaviors of in-situ carbides reinforced Ni-based composites by reactive sintering Ni and Ti2AlC precursor

High-temperature oxidation wear performance and mechanism of Cr–Mo (W)–V hot-work die steel