Abstract:Eutectic high entropy alloys are noted for their excellent castability and comprehensive mechanical properties. The excellent mechanical properties are closely related to the activation and evolution of deformation mechanisms at the atomic scale. In this work, AlCoCrFeNi 2.1 alloy is taken as the research object. The mechanical behaviors and deformation mechanisms of the FCC and B2 single crystals with different orientations and the FCC/B2 composites with K-S orientation relationship during nanoindentation processes are systematically studied by molecular dynamics simulations. The results show that the mechanical behaviors of FCC single crystals are significantly orientation-dependent, meanwhile, the indentation force of [110] single crystal is the lowest at the elastic–plastic transition point, and that for [100] single crystal is the lowest in plastic deformation stage. Compared with FCC, the stress for B2 single crystals at the elastic–plastic transition point is higher. However, more deformation systems such as stacking faults, twins and dislocation loops are activated in FCC single crystal during the plastic deformation process, resulting in higher indentation force. For composites, the flow stress increases with the increase of B2 phase thickness during the initial stage of deformation. When indenter penetrates heterogeneous interface, the significantly increased deformation system in FCC phase leads to a significant increase in indentation force. The mechanical behaviors and deformation mechanisms depend on the component single crystal. When the thickness of the component layer is less than 15 nm, the heterogeneous interfaces fail to prevent the dislocation slip and improve the indentation force. The results will enrich the plastic deformation mechanisms of multi-principal eutectic alloys and provide guidance for the design of nanocrystalline metallic materials.

Investigation on Behavior of Elastoplastic Deformation for Ti–48Al–2Cr–2Nb Alloy by Micro‐Indentation and FEM‐Reverse Algorithm

Use of Instrumented Micro-Indentation to Study the Mesoscopic Elasto-Plastic Behavior of Gh4145/Sq Superalloy During High-Temperature Cyclic Straining

A Study of Fatigue Mesoscopic Elasto-Plastic Properties of a Nickel-Base Superalloy by Instrumented Microindentation Measurements

Investigation of fatigue mesoscopic mechanical properties of a nickel-based superalloy by instrumented microindentation measurements

Young’s Modulus of Polycrystalline Titania Microspheres Determined by in Situ Nanoindentation and Finite Element Modeling

Experiments and crystal plasticity simulations for the deformation behavior of nanoindentation: Application to the α2 phase of TiAl alloy

Micro- and macroscopic plastic flow responses in high Nb-containing TiAl alloy by nanoindentation

Estimation of Mechanical Properties of Aluminum Alloy Based on Indentation Curve and Projection Area of Contact Zone

Research on Determining Elastic–Plastic Constitutive Parameters of Materials from Load Depth Curves Based on Nanoindentation Technology

Molecular dynamics simulation and experimental study on nanoindentation response of polycrystalline γ-TiAl alloy

Mechanical Properties of Micro-phases Along < 001 > Direction of Directionally Solidified Nickel-base Super-alloy by In-situ Nano-Indentation

An Inverse Approach to Determine the Mechanical Properties of Elastoplastic Materials Using Indentation Tests

Size-dependent sharp indentation-II: a reverse algorithm to identify plastic properties of metallic materials

NUMERICAL SIMULATION FOR CONE INDENTATION OF METALLIC FOAMS AND THE REVERSE ANALYSIS

Influence of Indenter Tip Roundness on Hardness Behavior in Nanoindentation

Probing the Crystal Structure and Dislocation Evolution in Single Crystal Al0.3CoCrFeNi High-Entropy Alloy under Nanoindentation

Combined crystal plasticity simulations and experiments for parameter identification: application to near-β titanium alloy

Molecular Dynamics Simulations of Micromechanical Behaviours for AlCoCrFeNi2.1 High Entropy Alloy during Nanoindentation

Berkovich indentation and the Oliver-Pharr method for shape memory alloys

Anisotropic elastic–plastic properties of surface-modified layers of 18CrNiMo7-6 alloy steel after carburizing heat treatment determined by an indentation method

Experimental and numerical investigations of anisotropic plasticity response in polycrystalline copper by nanoindentation