Abstract:The corrosion of steel structures in aggressive marine environments is a vital issue that induces significant degradation of their performance and lifespan. Herein, three arc-sprayed ZnAl coatings with varied Al contents of 0 wt.%, 15 wt.%, and 50 wt.% were deposited onto a hull steel substrate. The effect of Al content on the long-term corrosion protection performance of ZnAl coatings left in a chloride-containing solution for 840 h was systematically investigated. The evolutions of open-circuit potential, polarization curves, and electrochemical impedance spectroscopy of different ZnAl coatings during the long-term immersion test were examined. The morphologies and phase constitutions of the corrosion products were characterized. The results indicated that the corrosion rate of ZnAl coatings decreased as the Al content increased, and the ZnAl50 coating exhibited the most superior long-term corrosion protection performance. Moreover, for the three ZnAl coatings with an Al contents varying from 0 to 50%, their corrosion rate increased with immersion time in the initial 360 h due to the formation of the unstable and porous corrosion product ZnO; after 360 h immersion, their corrosion rate decreased with the prolonging of immersion time. This was revealed to be related to the formation of different corrosion products. ZnO and stable Al2O3 were the main corrosion products for the pure Zn coating and ZnAl15 coating, respectively. Al2O3 and powerful layered double hydroxide Zn6Al2(OH)16CO3·4H2O were found to be the dominant corrosion products of the ZnAl50 coating, which was responsible for its remarkable long-term corrosion protection performance.

Wetting Behaviour of Zn–Al Filler Metal on a Stainless Steel Substrate

Influence of Ni Addition on Corrosion Performance of Medium-temperature Filler Metal with Low Cu Content for Al Brazed Joints

Wetting and spreading behaviors of Al-Si alloy on surface textured stainless steel by ultrafast laser

Solidification microstructure of Zn-(0-6.0%)Al-4%Sb alloys used for hot-dip galvanizing

Wetting Kinetics and Microstructure Analysis of BNi2 Filler Metal over Selective Laser Melted Ti-6Al-4V Substrate

Microstructure, Mechanical Properties and Corrosion Behaviors of Al–Li–Cu–Mg–Ag–Zn Alloys

Molecular dynamics and first-principles calculations on the wetting behavior and mechanism of molten Al on nickel-infiltrated steel: A cross-scale simulation

Wetting of liquid Zinc-aluminum-magnesium alloy on steel substrate during hot-dipping: Understanding the role of the flux

Effect on Wetting Properties of the Al-Ti System by the Addition of Different Alloying Elements

Effect of Al Content on the Long-Term Corrosion Behavior of Arc-Sprayed ZnAl Alloy Coatings

Investigation on the microstructural evolution and corrosion behaviors of Zn-microalloyed Al-Cu-Li alloys

Influence of Al contents on the long-term corrosion behaviors of cold-sprayed Zn-xAl coatings

Effect of Al/Mg Ratio on the Microstructure and Phase Distribution of Zn-Al-Mg Coatings

Effects of Al-Mg on the Microstructure and Phase Distribution of Zn-Al-Mg Coatings

Effect of Al Content on the Microstructure and Properties of Zn-Al Solder Alloys

Characterisation of Fe Distribution in the Liquid–Solid Boundary of Al–Zn–Mg–Si Alloy Using Synchrotron X-ray Fluorescence Microscopy

Impacts of Zinc Layer and Pouring Method on Interface Performance for Al-22Si/ZL104 Bi-Metal

Al Alloy Melting Behavior and Interfacial Reactions with Steel Under Natural Convection

Development of novel CsF–RbF–AlF3 flux for brazing aluminum to stainless steel with Zn–Al filler metal

Enhancing the wettability for 4043 aluminum alloy on 301L stainless steel via chemical-etched surface texturing

Wetting and Interfacial Chemistry of New Pb-Free Sn-Zn-Ag-Al-Li (SZAAL) Solder with Cu, Ni, and Al Substrates