Abstract:Ti–6Cr–5Mo–5V–4Al (Ti-6554) alloy has wide applications for large load-bearing components in the aerospace field. However, during the hot forming process of the alloy in the α+β phase region, there are a variety of interaction and restriction softening mechanisms and complex texture evolution behaviors, which jointly affect the microstructure and mechanical properties. This paper systematically studies the softening mechanism and texture evolution of Ti-6554 alloy in the α+β phase region using electron backscatter diffraction (EBSD), including dynamic phase transformation (DPT) and dynamic spheroidization of α phase and dynamic recrystallization (DRX) of β phase. Firstly, the effect of deformation parameters on the DPT is studied, and it is found that the volume fraction of α phase declines gradually with raising the strain rate, deformation temperature and deformation amount. The yield stress and the driving force for DPT increase with raising the strain rate and decreasing the deformation temperature. The equiaxed α phase will gradually transform into the lamellar α phase during the spheroidization process, accompanied by the wedging of the β phase. The combined effect of DPT and dynamic spheroidization leads to α grain refinement. Furthermore, the effect of deformation parameters on the DRX process of β phase is also investigated. The DRX degree only increases gradually with increasing the strain. Increasing the deformation temperature and decreasing the strain rate do not significantly increase the DRX volume fraction. Meantime, the DRX process of the β phase is heavily dependent on the α phase. The higher proportion of the α phase is capable of promoting continuous dynamic recrystallization (CDRX) process of β phase, while the lower proportion of the α phase will promote the transformation of CDRX into dynamic recrystallization (DDRX), but can not effectively increase the DRX degree of β phase. Further, the texture evolution shows that due to the combined effect of DPT and dynamic spheroidization, the effect of deformation parameters on the texture strength of α phase is very complicated. For the β phase, and fiber textures are easily formed during the deformation process.

Study on the Deformation Behavior of Β Phase in Ti–10V–2Fe–3Al Alloy by Micro-Indentation

Use of Instrumented Micro-Indentation to Study the Mesoscopic Elasto-Plastic Behavior of Gh4145/Sq Superalloy During High-Temperature Cyclic Straining

Hot Deformation Behavior of a Novel Near-β Titanium Alloy Ti-5.5Mo-6V-7Cr-4Al-2Sn-1Fe in (α+β) Phase Region

In-situ Investigation Via High Energy X-ray Diffraction of Stress-Induced(0002)α→(110)β Transformation in a Ti-5.5Mo-7.2Al-4.5Zr-2.6Sn-2.1Cr Alloy

Mechanical Properties of Micro-phases Along < 001 > Direction of Directionally Solidified Nickel-base Super-alloy by In-situ Nano-Indentation

Experiments and crystal plasticity simulations for the deformation behavior of nanoindentation: Application to the α2 phase of TiAl alloy

Study on the Relationship Between Microstructure and Mechanical Property in a Metastable Β Titanium Alloy

The relationship between flow behavior and initial microstructure of Ti-10V-2Fe-3Al alloy during subtransus deformation

Molecular dynamics simulation and experimental study on nanoindentation response of polycrystalline γ-TiAl alloy

Phase Composition Effects on Dynamic Behavior and Strain Rate Sensitivity in Metastable β-Ti Alloys

Effect of phase content on mechanical properties and deformation mechanism in TC21 titanium alloy: An in-situ tensile investigation

Study on the Transformation of (α+β) Phase to Β Phase in Deformed Ti-6Al-4V Alloy During the Heat Treatment

Evolution of the α phase and microhardness for hot isostatic pressed Ti-6Al-4V alloy during multi-pass deformation

Microstructure and microhardness evolution of Ti-10V-2Fe-3Al alloy under tensile/torsional deformation modes

Effect of Hot Rolling Temperature on Microstructure Evolution, Deformation Texture and Nanoindentation Properties of an Intermetallic Ti-43Al-9V-0.2Y Alloy

Systematic analysis of the softening mechanism and texture evolution of Ti–6Cr–5Mo–5V–4Al alloy during hot compression in α+β phase region

Post-dynamic transformation from α to β phase and reverse transformation in Ti-10V-2Fe-3Al alloy during interrupted hot deformation

Micro- and macroscopic plastic flow responses in high Nb-containing TiAl alloy by nanoindentation

The role of the ω phase on the microstructure evolution of precipitation and mechanical property in Ti-3Al-5Mo-4Cr-2Zr-1Fe

Microstructure of the ordered β phase in TiAl alloy with chromium and vanadium

In- and ex-situ study of the deformation behavior of the βo(ωo) phase in a Ti4Al3Nb alloy during high-temperature compression