Abstract:Zr-6Al-0.1B alloy rich in Zr3Al phase is prepared by hot-pressing sintering. The thermal deformation behavior of sintered Zr-6Al-0.1B is analyzed by isothermal compression tests at deformation temperatures of 950, 1050, and 1150 °C with strain rates of 0.01, 0.1, and 1 s-1. The results indicate that at the early stage of thermal deformation, the stress increases rapidly with the increase of strain and then reaches the peak value. Subsequently, the stress decreases with the increase of strain under the softening effect. On the whole, the true stress-strain curve shifts to the high stress area with the increase of strain rate or the decrease of deformation temperature, so the sintered Zr-6Al-0.1B alloy belongs to the temperature and strain rate sensitive material. For the microstructure evolution of sintered Zr-6Al-0.1B during the isothermal compression, the high strain rate can improve the grain refinement. However, because sintered Zr-6Al-0.1B is a low plastic material, too high strain rate will exceed the deformation capacity of the material, resulting in an increase in defects. The increase of deformation temperature also contributes to grain refinement, but when the temperature is too high, due to the decomposition of Zr3Al phase, the deformation coordination of the material decreases, leading to the increase of the probability of the occurrence of defects. This study verified the feasibility of hot-pressing sintering to prepare Zr-6Al-0.1B alloy rich in Zr3Al phase and laid the foundation of "hot-pressing sintering + canning hot-extrusion" process of Zr-6Al-0.1B alloy components.

Investigation of the Characteristics of Submicron-Structured Powder-Fabricated Cr50ni50 Alloys Via Different Hot-Press Sintering Pressures

Effect of Process Parameters on the Microstructure and Mechanical Properties of Vacuum Hot-Press Sintered Co-50 Mass% Cr Alloys

Investigation of a Hot-Pressed Nb–Ti–Al Alloy: Mechanical Alloying, Microstructure and Mechanical Property

Nano-Al2o3 Reinforced Fe-Cr-Ni Composites Fabricated by Reactive Hot Pressing

Hot Deformation Characteristics of Ti43.5Al5Nb1V1Y Alloy by Hot Press Sintering

Improved Homogenization of Ni in Sintered Steels Through the Use of Cr-Containing Prealloyed Powders

Microstructure and Mechanical Properties of the Powder Metallurgy Nb-16Si-24Ti-2Al-2Cr Alloy

Effect of holding time and pressure on the densification, microstructure and mechanical properties of hot pressed Al2O3-CA6-ZrO2/Ni multi-phase composites

Fast Fabrication of In-Situ Micro-Nano Al_2O_3 Reinforced Fe-Cr-Ni Composites by Hot-Pressing at Low Temperature

Study on sintering of SHSTi3AlC2 powders by hot pressing

Microstructure and mechanical properties of in situ NiAl-Mo2C nanocomposites prepared by hot-pressing sintering

Investigations on the NiAl–Cr(Mo) Eutectic Alloy with Optimized Microstructure and Improved Room-Temperature Compressive Properties

Porous Nano-Al2o3/fe–cr–ni Composites Fabricated by Pressureless Reactive Sintering

Mechanical Properties and Oxidation Behavior of Hot Pressing Sintered Nb5Cr Superalloy

Influence of Spark Plasma Sintering Parameters on the Microstructure and Room-Temperature Mechanical Properties of NiAl-28Cr-5.5Mo-0.5Zr Alloy

Improvement In Microstructure Homogeneity Of Sintered Compacts Through Powder Treatments And Alloy Designs

Microstructure and Thermal Deformation Behavior of Hot-Pressing Sintered Zr-6Al-0.1B Alloy

Microstructure evolution, phase decomposition and transition of Al0.8Co0.5Cr1.5CuFeNi HEA during high temperature sintering and mechanical properties corresponding to different microstructures

Quasi-quantitative Control of the Properties at Room Temperature and 1000°C of NiAl-based Composites Prepared by Hot Press Sintering

Effect of Hot Isostatic Pressing on Microstructure and Mechanical Property of Nial/Cr(Mo,Hf) Composite