Abstract:In this article, we first review the current status of 400GBASE client-side optics standards and multi-source agreements (MSAs). We then compare different form factors for 400GE modules, including CFP8, OSFP and QSFP-DD. The essential techniques to implement 400GE, such as pulse amplitude modulation (PAM4), forward error correction (FEC) and a continuous time-domain linear equalizer (CTLE), are discussed. A 400GE physical interface card (PIC) in Juniper’s PTX5000 platform has been developed, conforming to the latest IEEE802.3bs standard. To validate the PIC’s performance, a commercial optical network tester (ONT) and the PIC are optically interconnected through two CFP8-LR8 modules. The CFP8-LR8 module utilizes eight optical wavelengths through coarse wavelength division multiplexing (CWDM). Each wavelength carries 50 Gb/s PAM4 signal. The signal transmits through 10 km of single mode fiber (SMF). The ONT generates framed 400GE signal and sends it to the PIC through the first CFP8 module. The PIC recovers the signal, performs an internal loopback, and sends 400GE signal back to the ONT through the second CFP8 module. The optical spectrum, eye diagram, receiver sensitivity, long time soaking results, and internal digital diagnosis monitoring (DDM) result are fully characterized. The pre-FEC bit error rate (BER) is well below the KP4 FEC threshold of 2.2 × 10−4. After KP4 FEC, error-free performance over 30 km of SMF is achieved. In this way, we demonstrate both the interoperation between the PIC and the ONT, as well as the interoperation between the two CFP8 modules. This demonstration represents the successful implementation of the 400GE interface in the core IP/MPLS router.

A 0.18 Μm CMOS Transmit Physical Coding Sublayer IC for 100G Ethernet

106.25 Gbaud On-Off Keying and Pulse Amplitude Modulation Links Supporting Next Generation Ethernet on Single Lambda

Design and Implementation of Coding Algorithm in Physical Coding Sublayer of Gigabit Ethernet

Design of the Physical Coding Sublayer Based on the Ethernet 10Gbase-R Protocol

An 11.05 Mw/Gbps Quad-Channel 1.25-10.3125 Gbps Serial Transceiver With A 2-Tap Adaptive Dfe And A 3-Tap Transmit Ffe In 40 Nm Cmos

A Single-Routing Layered LDPC Decoder for 10Gbase-T Ethernet in 130nm CMOS

A Fully Integrated CMOS Gigabit Ethernet Serialize & De-Serialize Transceiver Chip

A 0.18 μm CMOS 10-Gb/S multichannel transmitter with duty-cycle correction

A 10Gb/s source-synchronous transmitter in 65nm CMOS technology

A Power Efficient 1.0625-3.125 Gb/s Serial Transceiver in 130 Nm Digital CMOS for Multi-Standard Applications.

400Gbe Technology Demonstration Using CFP8 Pluggable Modules

A 10gb/s Compact Low-Power Serial I/O with DFE-IIR Equalization in 65nm CMOS

3.125Gb/s Transmitter with 0.18μm CMOS Process

Design of codec for the physical layer of 100G Ethernet

10&Amp;#x00d7;100-Gb/s Transmissions Using Optical Carrier Suppression and Separation Technique and RZ-DQPSK Modulation for Metro-Ethernet Transport System

Design of an In-line Packet Transceiver for 10 Gb/s Ethernet

800 Gbit/s QSFP-DD Transceiver Based on Thin-film Lithium Niobate Photonic Integrated Circuit

Design and performance evaluation of 100 Gb/s LDPC-coded polarization division multiplexing CO-OFDM physical layer

A CMOS 3.125 Gb/s Receiver for Multichannel 10 Gbit Ethernet Interface

A 10-Gb/s 5-Tap DFE/4-Tap FFE Transceiver in 90-Nm CMOS Technology

A 32gb/s 133mw PAM-4 Transceiver with DFE Based on Adaptive Clock Phase and Threshold Voltage in 65nm CMOS.