Predicting High Thermoelectric Performance of ABX Ternary Compounds NaMgX (X = P, Sb, As) with Weak Electron–phonon Coupling and Strong Bonding Anharmonicity

A. J. Hong,J. J. Gong,L. Li,Z. B. Yan,Z. F. Ren,J. -M. Liu

DOI: https://doi.org/10.1039/c6tc00461j

IF: 6.4

2016-01-01

Journal of Materials Chemistry C

Abstract:The ABX ternary compounds have a variety of attractive physical properties.

What problem does this paper attempt to address?

The Influence of Strong Anharmonicity on High Thermoelectric Properties for the Ternary Compound NaMgX (X = As, Sb)

Peipei Liu,Yinchang Zhao,Jianying Cui,Jun Ni,Sheng Meng,Zhenhong Dai

DOI: https://doi.org/10.1016/j.cplett.2023.140521

IF: 2.719

2023-01-01

Chemical Physics Letters

Abstract:We theoretically analyzed the thermoelectric characteristics of the tetragonal NaMgX (X = As, Sb) compounds with strongly quartic anharmonicity based on an incorporation of first-principles calculations with self -consistent phonon theory and Boltzmann transport equations. These two materials show the low lattice thermal conductivity due to the low phonon group velocity. Since the flat band and the dispersion band coexist near the Fermi surface, the ZT values of p-type NaMgAs and NaMgSb at 900 K along the a(b) axis are 1.27 and 2.29, respectively. These results show that these two materials have good thermoelectric properties.
Anisotropic thermoelectric properties of Weyl semimetal NbX (X = P and As): a potential thermoelectric material.

Yu Zhou,Ying-Qin Zhao,Zhao-Yi Zeng,Xiang-Rong Chen,Hua-Yun Geng

DOI: https://doi.org/10.1039/c9cp02020a

IF: 3.3

2019-01-01

Physical Chemistry Chemical Physics

Abstract:Weyl semimetal, a newly developed thermoelectric material, has aroused much interest due to its extraordinary transport properties. In this work, the thermoelectric transport properties of NbX (X = P and As), a prototypical Weyl semimetal, are investigated using the first-principles calculations together with Boltzmann transport theory. The calculated room-temperature lattice thermal conductivities along the a and c directions are 2.0 W mK(-1) and 0.6 W mK(-1) for NbP and 1.4 W mK(-1) and 0.4 W mK(-1) for NbAs, respectively. The low thermal conductivities may be useful in the thermoelectric applications. It is found that the acoustic branches have obvious contribution to the total lattice thermal conductivity, and the size dependence of the thermal conductivities can provide guidance for designing thermoelectric nanostructures. Our results show that the anisotropic structures of these compounds bring about the anisotropy of transport coefficients along the a and c directions, and the preferred direction is the c direction in thermoelectric applications. Moreover, NbP and NbAs show high ZT values of 0.82 and 0.50 along the c direction for p-type at an optimal carrier concentration, indicating that they are potential thermoelectric materials.
Study on the Thermoelectric Characteristics of the Ternary Alkali Metal Compound XMgSb (X = K, Rb, Cs)

Yue Wang,Yinchang Zhao,Baolong Xu,Jun Ni,Sheng Meng,Zhenhong Dai

DOI: https://doi.org/10.1088/1361-6463/ace066

2023-01-01

Abstract:We conducted a comprehensive analysis of the mechanical, transport, and thermoelectric (TE) characteristics of XMgSb (X = K, Rb, Cs) alkali metal compounds using first-principles calculations, self-consistent phonon theory, pressive sensing lattice dynamics, and the Boltzmann transport equation. Our results show that the very low lattice thermal conductivity of these materials is mainly attributed to the strong anharmonicity of the alkali metal atoms, and the lattice thermal conductivity is negatively correlated with the mass of X atoms. Furthermore, we consider five scattering mechanisms to accurately calculate transport properties and electron relaxation times. Notably, we observed that the large electronic dispersion band near the valence band maximum leads to the high conductivity of these three compounds, with a flat electronic energy band at the & UGamma;-Z point, which generally implies a larger Seebeck coefficient. The coexistence of good electronic band dispersion and flat electronic bands leads to high conductivity and large Seebeck coefficient, resulting in high TE power. Low lattice thermal conductivity and high TE power factor jointly determine the development potential of alkali metal compound XMgSb (X = K, Rb, Cs) in the field of TE.
Ternary mixed-anion semiconductors with tunable band gaps from machine-learning and crystal structure prediction

Maximilian Amsler,Logan Ward,Vinay I. Hegde,Maarten G. Goesten,Xia Yi,Chris Wolverton

DOI: https://doi.org/10.1103/PhysRevMaterials.3.035404

2018-12-07

Abstract:We report the computational investigation of a series of ternary X$_4$Y$_2$Z and X$_5$Y$_2$Z$_2$ compounds with X={Mg, Ca, Sr, Ba}, Y={P, As, Sb, Bi}, and Z={S, Se, Te}. The compositions for these materials were predicted through a search guided by machine learning, while the structures were resolved using the minima hopping crystal structure prediction method. Based on $\textit{ab initio}$ calculations, we predict that many of these compounds are thermodynamically stable. In particular, 21 of the X$_4$Y$_2$Z compounds crystallize in a tetragonal structure with $\textit{I-42d}$ symmetry, and exhibit band gaps in the range of 0.3 and 1.8 eV, well suited for various energy applications. We show that several candidate compounds (in particular X$_4$Y$_2$Te and X$_4$Sb$_2$Se) exhibit good photo absorption in the visible range, while others (e.g., Ba$_4$Sb$_2$Se) show excellent thermoelectric performance due to a high power factor and extremely low lattice thermal conductivities.

Materials Science
Strong anharmonicity and medium-temperature thermoelectric efficiency in antiperovskites Ca3XN (X = P, As, Sb, Bi) compounds

Shuyao Lin,jincheng Yue,Wenling Ren,Chen Shen,Hongbin Zhang

DOI: https://doi.org/10.1039/d4ta02118e

IF: 11.9

2024-06-27

Journal of Materials Chemistry A

Abstract:In this work, we employ density functional theory (DFT) calculations to systematically investigate the thermal and electronic transport properties, as well as the thermoelectric performance, of antiperovskite (APV) compounds within the Ca 3 XN family, where X = P, As, Sb, and Bi. Such calculations are performed based on the self-consistent phonon (SCP) theory and the Boltzmann transport equation, specifically accounting for four-phonon scattering processes. Interestingly, these materials display notably low thermal conductivity (κ L ), approximately 1.1 W/m·K at 900 K. As a result, both Ca 3 AsN and Ca 3 SbN exhibit remarkably high figure of merit ( ZT ) values at elevated temperatures (300-900 K), exceeding 1.1. Moreover, within selected APV materials, especially Ca 3 AsN, Ca 3 SbN, and Ca 3 BiN, maintain promising thermoelectric properties also in the medium-temperature range (≈600 K), with ZT values of approximately 0.8, alongside unconventional temperature-dependent thermal conductivities. Our work serves as a proof-of-concept example for designing materials in future medium/high-temperature thermoelectric applications.

materials science, multidisciplinary,chemistry, physical,energy & fuels
High-throughput screening of potentially ductile and low thermal conductivity ABX3 (X = S, Se, Te) thermoelectric perovskites

Yan Cao,Shengnan Dai,Xiangdong Wang,Tianran Wei,Jiong Yang,Lili Xi,Zhenqian Pang,Gang Tan

DOI: https://doi.org/10.1063/5.0188454

IF: 4

2024-02-26

Applied Physics Letters

Abstract:Chalcogenide perovskites, renowned for their low lattice thermal conductivity, have emerged as promising candidates for thermoelectric applications. Hence, we leveraged first-principles high-throughput calculations to investigate the electrical and thermal transport properties, as well as the ductility, of the chalcogenide perovskites ABX3 (X = S, Se, Te). Candidates with 30 combinations were initially screened by bandgap screening (Eg > 0.1 eV), stability assessment (Born–Huang criterion), and ductility evaluation (Pugh's ratio: G/K < 0.571, the ratio of shear modulus G to bulk modulus K) from the MatHub-3d database (176 ABX3 crystal structures, 32 kinds of space groups, and number of atoms Natom < 40). Intriguingly, weaker chemical bonding between the A and X site atom pairs gives rise to a higher ductility in the screened quasi-ductile perovskites. Furthermore, it should be noted that the low phonon group velocities confirmed the low lattice thermal conductivity of the materials. In consequence, the identification of quasi-ductile thermoelectrics, characterized by six n-type and six p-type candidates with ZT > 0.3 at 300 K, stands as the most promising candidates for application in thermoelectrics.

physics, applied
Electronic Orbital Alignment and Hierarchical Phonon Scattering Enabling High Thermoelectric Performance p-Type Mg 3 Sb 2 Zintl Compounds

Jinsuo Hu,Jianbo Zhu,Fengkai Guo,Haixu Qin,Yijie Liu,Qian Zhang,Zihang Liu,Wei Cai,Jiehe Sui

DOI: https://doi.org/10.34133/2022/9842949

IF: 11

2022-04-29

Research

Abstract:Environmentally friendly Mg 3 Sb 2 -based materials have drawn intensive attention owing to their promising thermoelectric performance. In this work, the electrical properties of p-type Mg 3 Sb 2 are dramatically optimized by the regulation of Mg deficiency. Then, we, for the first time, found that Zn substitution at the Mg2 site leads to the alignment of p x , y and p z orbital, resulting in a high band degeneracy and the dramatically enhanced Seebeck coefficient, demonstrated by the DFT calculations and electronic properties measurement. Moreover, Zn alloying decreases Mg1 (Zn) vacancies formation energy and in turn increases Mg (Zn) vacancies and optimizes the carrier concentration. Simultaneously, the Mg/Zn substitutions, Mg vacancies, and porosity structure suppress the phonon transport in a broader frequency range, leading to a low lattice thermal conductivity of ~0.47 W m -1 K -1 at 773 K. Finally, a high ZT of ~0.87 at 773 K was obtained for Mg 1.95 Na 0.01 Zn 1 Sb 2 , exceeding most of the previously reported p-type Mg 3 Sb 2 compounds. Our results further demonstrate the promising prospects of p-type Mg 3 Sb 2 -based material in the field of mid-temperature heat recovery.

multidisciplinary sciences
Predicting the optimized thermoelectric performance of MgAgSb

C. Y. Sheng,H. J. Liu,D. D. Fan,L. Cheng,J. Zhang,J. Wei,J. H. Liang,P. H. Jiang,J. Shi

DOI: https://doi.org/10.1063/1.4949479

IF: 2.877

2016-05-21

Journal of Applied Physics

Abstract:Using first-principles method and Boltzmann theory, we provide an accurate prediction of the electronic band structure and thermoelectric transport properties of α-MgAgSb. Our calculations demonstrate that only when an appropriate exchange-correlation functional is chosen can we correctly reproduce the semiconducting nature of this compound. By fine tuning the carrier concentration, the thermoelectric performance of α-MgAgSb can be significantly optimized, which exhibits a strong temperature dependence and gives a maximum ZT value of 1.7 at 550 K. We also provide a simple map by which one can efficiently find the best doping atoms and optimal doping content.

physics, applied
Thermoelectric Performance of Zintl Compound KMgBi with Layered Structure

Aixian She,Yinchang Zhao,Jun Ni,Sheng Meng,Zhenhong Dai

DOI: https://doi.org/10.1016/j.jpcs.2023.111308

IF: 4.383

2023-01-01

Journal of Physics and Chemistry of Solids

Abstract:Zintl compounds are potential candidates for thermoelectric (TE) materials because of their excellent electronic transport combined with low thermal conductivity. We have systematically investigated the thermal, electronic transport, and TE properties of the anisotropic orthorhombic KMgBi crystal on the basis of first-principles calculations together with self-consistent phonon theory, the compressed sensing technique, and the Boltzmann transport equation. When predicting electron transport parameters, we take into account the impacts of acoustic deformation potential scattering, polar optical phonon scattering, and ionized impurity scattering on electron relaxation times. Strikingly, the layered structure of the Zintl compound KMgBi results in the material exhibiting strong anisotropy. This layered structure provides a good transport channel for electrons along the a(b)-axis, which results in a large difference in electrical conductivity and thermal conductivities between the a(b)-axis and the c-axis. Because of the high power factor obtained along the a(b)-axis, the figure of merit (ZT) is expected to reach 1.5 at 600 K and KMgBi is a promising candidate for high-temperature TE applications.
Theoretical investigation of the lattice thermal conductivities of II-IV-V2 pnictide semiconductors

Victor Posligua,Jose J. Plata,Antonio M. Márquez,Javier Fdez Sanz,Ricardo Grau-Crespo

2023-09-08

Abstract:Ternary pnictides semiconductors with II-IV-V2 stoichiometry hold potential as cost effective thermoelectric materials with suitable electronic transport properties, but their lattice thermal conductivities ($\kappa$) are typically too high. Gaining insight into their vibrational properties is therefore crucial to finding strategies to reduce $\kappa$ and achieve improved thermoelectric performance. We present a theoretical exploration of the lattice thermal conductivities for a set of pnictide semiconductors with ABX2 composition (A = Zn, Cd; B = Si, Ge, Sn; and X = P, As), using machine-learning based regression algorithms to extract force constants from a reduced number of density functional theory simulations, and then solving the Boltzmann transport equation for phonons. Our results align well available experimental data, decreasing the mean absolute error by ~3 Wm-1K-1 with respect to the best previous set of theoretical predictions. Zn-based ternary pnictides have, on average, more than double the thermal conductivity of the Cd-based compounds. Anisotropic behaviour increases with the mass difference between A and B cations, but while the nature of the anion does not affect the structural anisotropy, the thermal conductivity anisotropy is typically higher for arsenides than for phosphides. We identify compounds, like CdGeAs2, for which nanostructuring to an affordable range of particle sizes could lead to values low enough for thermoelectric applications.

Materials Science
Low lattice thermal conductivities and good thermoelectric performance of hexagonal antiperovskites X(Ba & Sr)3BiN with quartic anharmonicity

Shuming Zeng,Xiang Yan,Qian Shen,Yusong Tu,Hao Huang,Geng Li

DOI: https://doi.org/10.1039/d3cp03248e

2023-10-11

Abstract:Antiperovskites are a burgeoning class of semiconducting materials that showcase remarkable optoelectronic properties and catalytic properties. However, there has been limited research on their thermoelectric properties. Combining first-principles calculations, self-consistent phonon theory and the Boltzmann transport equation, we have discovered that the hexagonal antiperovskites X(Ba & Sr)3BiN exhibit strong quartic lattice anharmonicity, where the anharmonic vibrations of the light N atoms primarily affect the lattice thermal conductivity (κL) along the c-axis direction. As a result, the lattice thermal conductivities along the a(b)-axis direction are low. At 300 K, the κL values of Ba3BiN and Sr3BiN are only 1.27 W m-1 K-1 and 2.24 W m-1 K-1, respectively. Moreover, near the valence band maximum, the orbitals of the N atoms dominate. This dominance allows Sr3BiN to achieve high power factor under p-type doping, resulting in an impressive thermoelectric figure of merit (ZT) of 0.94 along the c-axis direction at 800 K. In the a(b)-axis direction, at 800 K, n-type doped Ba3BiN exhibits a ZT value of 1.47, surpassing that of traditional thermoelectric materials. Our research elucidates that the hexagonal antiperovskites X(Ba & Sr)3BiN represent a category of potential thermoelectric materials with pronounced anisotropy, low thermal conductivity, and high thermoelectric performance.
Na/Bi-co-doping and Heterogeneous Interfaces Leading to Enhanced Thermoelectric Performance of P-Type Mg3Sb2-based Zintls

Zhe Xu,Xiao-Lei Shi,Yibo Zhang,Jisheng Liang,Meng Li,Chengyan Liu,Lei Miao,Siqi Liu,Shihao Wang,Qi Zhou,Jie Gao,Zhongwei Zhang,Wei-Di Liu,Ying Peng,Jun-Liang Chen,Zhi-Gang Chen

DOI: https://doi.org/10.1016/j.cej.2024.155147

IF: 15.1

2024-01-01

Chemical Engineering Journal

Abstract:Owing to the non-toxicity and low cost, Mg3Sb2-based Zintls are promising candidates for mid-temperature thermoelectric applications. However, the thermoelectric performance of p-type Mg3Sb2 is significantly lower than that of n-type ones. Here, we achieve simultaneous optimization of the band structure and enhanced phonon scattering through the combined doping of Na at the cation site and Bi at the anion site, leading to a competitive figure of merit, ZT of 0.73 at 773 K and a maximum theoretical energy conversion efficiency of 6.5 % at a temperature difference of 450 K. First-principles calculations indicate that Na and Bi co-doping effectively narrows the band gap and shifts the Fermi level into the valence band, thereby increasing the hole carrier concentration. This ensures a relatively high Seebeck coefficient and improved electrical conductivity, resulting in an excellent power factor of 7.5 mu W cm(-1) K-2. Additionally, by adjusting the amount of Bi nanoprecipitates in the matrix, the heterogeneous interfaces significantly enhance phonon scattering and markedly reduce the lattice thermal conductivity (0.52 W m(-1) K-1), collectively leading to the high thermoelectric performance. Furthermore, by pairing n-type Mg3.18Y0.02Sb1.5Bi0.49Se0.01, a double-leg thermoelectric device achieves an energy conversion efficiency of 4.1 % with a temperature difference of 390 K.
Theoretical Prediction of Mechanics, Transport, and Thermoelectric Properties of Full Heusler Compounds Na2KSb and X2CsSb (X = K, Rb)

Tongcai Yue,Pengfei Sui,Yinchang Zhao,Jun Ni,Sheng Meng,Zhenhong Dai

DOI: https://doi.org/10.1103/physrevb.105.184304

IF: 3.7

2022-01-01

Physical Review B

Abstract:Full Heusler compounds have become a research hotspot in the thermoelectric (TE) field, because they have the remarkable electronic properties and high-TE power factor. Nevertheless, the inherent high thermal conductivity KL hinders their further application as TE device. Hence, we investigate the mechanical, transport, and thermoelectric properties in Na2KSb and X2CsSb (X = K, Rb) with eight valence electrons per formula unit (f.u.) by using the first-principles calculations combined with self-consistent phonon (SCP) theory, compressive sensing (CS) techniques, and Boltzmann transport equation (BTE). Due to the strong three phonon scattering combined with small phonon group velocity, we obtain the ultralow lattice thermal conductivities. An evaluation of their mechanical properties reveals that they are all brittle compounds, and Rb2CsSb has the strongest elastic anisotropy. To capture rational electron transport properties, we include the effects of the acoustic deformation potential (ADP) scattering, polar optical phonon (POP) scattering, and ionized impurity (IMP) scattering on the electron relaxation time. Finally, a high p-type ZT values of 2.74 (2.48) at 600 (900) K are captured in the cubic K2CsSb (Na2KSb). These findings not only help us to comprehensively understand the physical properties of full Heusler compounds with eight valence electrons per f.u., but also support them as potential candidates for thermal management and thermoelectric applications.
Giant phonon anharmonicity driven by the asymmetric lone pairs in Mg3Bi2

Y. Zhu,J. Liu,B. Wei,S. Xu,Y. Song,X. Wang,T.-L. Xia,J. Chen,G.J. Snyder,J. Hong,Y. Zhu,J. Liu,B. Wei,S. Xu,Y. Song,X. Wang,T.-L. Xia,J. Chen,G.J. Snyder,J. Hong

DOI: https://doi.org/10.1016/j.mtphys.2022.100791

IF: 11.021

2022-10-01

Materials Today Physics

Abstract:Mg3Bi2-based materials exhibit high thermoelectric performance at ambient temperature benefitting from their low lattice thermal conductivity. However, the underlying physics of this low lattice thermal conductivity in a simple hexagonal crystal structure of Mg3Bi2 remain puzzling. Understanding the microscopic thermal transport behavior and its correlation with bonding, lattice dynamics are critical to improve the thermoelectric performance and design new promising functional materials. In this work, the giant anharmonic phonon modes are experimentally observed via measuring temperature-dependent inelastic x-ray scattering (IXS) for Mg3Bi2 single-crystal, which is also verified by the anomalously large Grüneisen parameters and frozen phonon potential calculations. Furthermore, we propose that the giant anharmonicty is associated with the asymmetric Bismuth 6s lone-pair electrons. The present work builds a microscopic connection between electronic structure and giant anharmonic phonon scattering, providing new insights on the low lattice thermal conductivity of Mg3Bi2, and paves the way to design novel high-efficient thermoelectrics for application in energy recycling and refrigeration.

materials science, multidisciplinary,physics, applied
Thermoelectric performance of (AgBiTe2)1-x(SnTe)x with stable cubic enabled by enhanced configurational entropy

Ting Zhao,Li-Ze Yang,Yun Zhou,Hui-Jun Liao,Zheng-Yong Huang,Jian Li,Xu Lu,Xiao-Yuan Zhou

DOI: https://doi.org/10.1007/s12598-022-02099-7

IF: 6.318

2022-11-08

Rare Metals

Abstract:ABX 2 (A = Ag, Na, Cu; B = Sb, Bi; X = S, Se, Te) (Groups I-V-VI 2 ) compounds, which are all characterized by the ultralow lattice thermal conductivity because of their strong lattice anharmonicity caused by lone-pair electrons, have aroused wide attention in thermoelectric community. The practical application of thermoelectric devices usually requires both the compatible n-type and p-type materials simultaneously. However, most of I-V-VI 2 compounds are intrinsic p-type semiconductors, lacking their n-type counterparts for thermoelectrics. Herein, in this work, we increase the configuration entropy of AgBiTe 2 by alloying SnTe, in order to stabilize the cubic phase at room temperature. With further optimization of thermal and electrical performance, the thermoelectric performance could be improved simultaneously in both n- and p-type (AgBiTe 2 ) 1- x (SnTe) x ( x = 0.3, 0.4) solid solutions. Finally, p-type compound with the nominal composition of (AgBi 0.99 Cd 0.01 Te 2 ) 0.6 (SnTe) 0.4 and n-type of (AgBiTe 2 ) 0.7 (SnTe) 0.3 ~ Br 6% show the maximum zT of ~ 0.33 and ~ 0.21, at 381 and 423 K, respectively.

materials science, multidisciplinary,metallurgy & metallurgical engineering
Thermoelectric Performance of Binary Lithium-Based Compounds: Li3Sb and Li3Bi

Kunling Peng,Zizhen Zhou,Honghui Wang,Hong Wu,Jianjun Ying,Guang Han,Xu Lu,Guoyu Wang,Xiaoyuan Zhou,Xianhui Chen

DOI: https://doi.org/10.1063/5.0056880

IF: 4

2021-01-01

Applied Physics Letters

Abstract:Thermoelectric transport properties of binary lithium-based compounds Li3Sb and Li3Bi are investigated. Although the present results show zTs (0.3 for Li3Sb and 0.06 for Li3Bi) are low for the p-type compounds in this family, the experimental data analysis based on the single parabolic band model assuming the dominance of acoustic phonon scattering for carriers suggests that both Li3Sb and Li3Bi process good electronic quality factor BE over 3, which gives rise to the predicted peak zT values above 0.7 and 1.2 at 800 K for Li3Sb and Li3Bi, respectively. In addition, the electronic band structure and phonon dispersion of Li3Sb are given by first principles calculation. This work offers insight into the crystal structure and transport properties of Li3Sb and Li3Bi, indicating the potential of binary lithium-based compounds as promising thermoelectrics.
Hierarchical Chemical Bonds Contributing to the Intrinsically Low Thermal Conductivity in Α‐mgagsb Thermoelectric Materials

Pingjun Ying,Xin Li,Yancheng Wang,Jiong Yang,Chenguang Fu,Wenqing Zhang,Xinbing Zhao,Tiejun Zhu

DOI: https://doi.org/10.1002/adfm.201604145

IF: 19

2016-01-01

Advanced Functional Materials

Abstract:Understanding the lattice dynamics and phonon transport from the perspective of chemical bonds is essential for improving and finding high‐efficiency thermoelectric materials and for many applications. Here, the coexistence of global and local weak chemical bonds is elucidated as the origin of the intrinsically low lattice thermal conductivity of non‐caged structure Nowotny–Juza compound, α‐MgAgSb, which is identified as a new type of promising thermoelectric material in the temperature range of 300–550 K. The global weak bonds of the compound lead to a low sound velocity. The unique three‐centered MgAgSb bonds in α‐MgAgSb vibrate locally and induce low‐frequency optical phonons, resulting in “rattling‐like” thermal damping to further reduce the lattice thermal conductivity. The hierarchical chemical bonds originate from the low valence electron count of α‐MgAgSb, with the feature shared by Nowotny–Juza compounds. Low lattice thermal conductivities are therefore highly possible in this series of compounds, which is verified by phonon and bulk modulus calculations on some of the compositions.
Enhancing thermoelectric performance of AB 2 Sb 2 -type Zintl phase through band shaping and lattice distortion

Qi Xu,Kunpeng Zhao,Haoran Huang,Shun Wan,Qingyong Ren,Xiaowen Hao,Hexige Wuliji,Jingdan Lei,Tian-Ran Wei,Xun Shi

DOI: https://doi.org/10.1016/j.actamat.2024.120040

IF: 9.4

2024-05-26

Acta Materialia

Abstract:AB 2 Sb 2 -type Zintl phases, especially Mg 3 Sb 2 , have garnered widespread attention in virtue of their nontoxic constituent elements and outstanding thermoelectric performance in n-type materials. However, the p-type counterpart of AB 2 Sb 2 still struggles with a low figure of merit zT , primarily because of the limited valence band degeneracy, large band effective mass, and relatively high thermal conductivity. Here we simultaneously optimize the electrical and thermal transports of p-type AB 2 Sb 2 -based materials through shaping the band edge and distorting the crystal lattice. By alloying Zn at Mg2 site and Ca at Mg1 site, we successfully decorate the crystal lattice of Mg 3 Sb 2 in real space and thereby modify the band structure in reciprocal space. Zn alloying promotes the band degeneracy while Ca alloying reduce the single band effective mass, which largely promotes the transport of charge carriers. Moreover, the distorted crystal lattice effectively blocks the heat-carry phonons to reduce the lattice thermal conductivity κ L . A high zT of 0.81 is finally realized at 750 K in our Zn/Ca co-alloyed samples, which is three times larger than that of Mg 3 Sb 2 matrix. Our work opens new possibilities for the synthetic optimization of both electrical and thermal transports in Zintl phase and other thermoelectric systems.

materials science, multidisciplinary,metallurgy & metallurgical engineering
Room Temperature High Thermoelectric Performance of Bi-based Full-Heusler Compounds Cs Rb3−xBi with Strong Anharmonicity

Shuming Zeng,Qian Shen,Lei Fang,Zonglin Gu,Jinpeng Yang,Geng Li,Yusong Tu,Jun Ni

DOI: https://doi.org/10.1016/j.ijheatmasstransfer.2023.124628

IF: 5.2

2023-01-01

International Journal of Heat and Mass Transfer

Abstract:Bismuth-based compounds have been identified as a class of promising candidates for the realization of high-performance thermoelectrics, derived from their exceptional electrical conductivity and intrinsic low lattice thermal conductivity κL. Here, we employed first-principles calculations, self-consistent phonon theory, and compressive sensing technique in conjunction with the Boltzmann transport equation to investigate the anharmonic thermoelectric properties of full-heusler bismuth compounds CsxRb3−xBi. As the Cs content increases, the κL of CsxRb3−xBi decreases due to impurity scattering effects, and then increases. Among them, at 300 K, Rb3Bi has the largest κL of 0.69 Wm−1K−1, while Cs2RbBi has the smallest κL of 0.45 Wm−1K−1, both of which are lower than the κL of traditional bismuth-based thermoelectric materials. The ultralow κL originates from the strong lattice anharmonicity. In addition, the coexistence of high dispersion and flat band edges leads to high thermoelectric power factor at optimal doping concentration. As a result, the largest thermoelectric figure of merit ZT values of 2.59 (4.19) at 300 (500) K were obtained for CsRb2Bi at optimal hole doping level. These findings suggest that CsxRb3−xBi compounds are superior for thermal management and thermoelectric applications.
Weak-Bonding Elements Lead to High Thermoelectric Performance in BaSnS 3 and SrSnS 3 : A First-Principles Study

Zhi Li,Hongyao Xie,Yi Xia,Shiqiang Hao,Koushik Pal,Mercouri G. Kanatzidis,Christopher Wolverton,Xinfeng Tang

DOI: https://doi.org/10.1021/acs.chemmater.1c03987

IF: 10.508

2022-01-20

Chemistry of Materials

Abstract:SnS2, an earth-abundant and ecofriendly material, is limited as a thermoelectric material because of the high lattice thermal conductivity κL and low carrier mobility μ. By introducing weak-bonding elements Ba or Sr into the SnS2 framework, we discovered two SnS2-based materials BaSnS3 and SrSnS3 with the calculated low κL values of 0.15 and 0.17 W m–1 K–1, respectively, along the a-axis. The low group velocity and high lattice anharmonicity originating from the weakened and distorted Sn–S bonding network are found in both systems. Moreover, the vibrations of Ba and Sr induce low-lying optical phonons, which strongly couple with the acoustic phonons and strengthen the phonon scattering rates. Compared to SnS2, both compounds present lower single-band effective masses, smaller deformation potential constants, and better band convergence, which enhance μ with an insignificantly reduced effective mass. By solving the linearized Boltzmann transport equation with a nonempirical carrier lifetime, we predict excellent ZT values of 2.89 and 2.77 along the a-axis at 900 K in BaSnS3 and SrSnS3, respectively. Further phase diagram calculations of Ba1–x Sr x SnS3 solid solutions propose a new compound, Ba0.5Sr0.5SnS3, with an even higher ZT of 3.0. Our work analyzes explicitly how weak-bonding elements enhance μ and suppress κL simultaneously in SnS2-analogous systems with a series of compounds nominated as potential high-performance thermoelectric materials.

materials science, multidisciplinary,chemistry, physical

Predicting High Thermoelectric Performance of ABX Ternary Compounds NaMgX (X = P, Sb, As) with Weak Electron–phonon Coupling and Strong Bonding Anharmonicity

The Influence of Strong Anharmonicity on High Thermoelectric Properties for the Ternary Compound NaMgX (X = As, Sb)

Anisotropic thermoelectric properties of Weyl semimetal NbX (X = P and As): a potential thermoelectric material.

Study on the Thermoelectric Characteristics of the Ternary Alkali Metal Compound XMgSb (X = K, Rb, Cs)

Ternary mixed-anion semiconductors with tunable band gaps from machine-learning and crystal structure prediction

Strong anharmonicity and medium-temperature thermoelectric efficiency in antiperovskites Ca3XN (X = P, As, Sb, Bi) compounds

High-throughput screening of potentially ductile and low thermal conductivity ABX3 (X = S, Se, Te) thermoelectric perovskites

Electronic Orbital Alignment and Hierarchical Phonon Scattering Enabling High Thermoelectric Performance p-Type Mg 3 Sb 2 Zintl Compounds

Predicting the optimized thermoelectric performance of MgAgSb

Thermoelectric Performance of Zintl Compound KMgBi with Layered Structure

Theoretical investigation of the lattice thermal conductivities of II-IV-V2 pnictide semiconductors

Low lattice thermal conductivities and good thermoelectric performance of hexagonal antiperovskites X(Ba & Sr)3BiN with quartic anharmonicity

Na/Bi-co-doping and Heterogeneous Interfaces Leading to Enhanced Thermoelectric Performance of P-Type Mg3Sb2-based Zintls

Theoretical Prediction of Mechanics, Transport, and Thermoelectric Properties of Full Heusler Compounds Na2KSb and X2CsSb (X = K, Rb)

Giant phonon anharmonicity driven by the asymmetric lone pairs in Mg3Bi2

Thermoelectric performance of (AgBiTe2)1-x(SnTe)x with stable cubic enabled by enhanced configurational entropy

Thermoelectric Performance of Binary Lithium-Based Compounds: Li3Sb and Li3Bi

Hierarchical Chemical Bonds Contributing to the Intrinsically Low Thermal Conductivity in Α‐mgagsb Thermoelectric Materials

Enhancing thermoelectric performance of AB 2 Sb 2 -type Zintl phase through band shaping and lattice distortion

Room Temperature High Thermoelectric Performance of Bi-based Full-Heusler Compounds Cs Rb3−xBi with Strong Anharmonicity

Weak-Bonding Elements Lead to High Thermoelectric Performance in BaSnS 3 and SrSnS 3 : A First-Principles Study