Abstract:Mg–1Mn alloy, extruded at a low temperature in our published protocol, contributed to the intensified basal texture and extremely refined microstructure with spheroidal nanoscale precipitates dispersing throughout the matrix and along the grain boundaries, consequently resulting in the excellent mechanical properties where the alloy exhibited a tensile yield strength of 204.3 MPa and a ductility of 38.8% at room temperature. Therefore, Mg–1Mn alloy was recommended as one of the potential materials for structural applications. In the present investigation, hot deformation behavior through constitutive analysis and extrusion temperature-dependent microstructure, texture and mechanical properties of as-extruded Mg–1Mn alloy were investigated, aiming at revealing how extrusion temperature affected microstructure, texture, and mechanical properties of as-extruded Mg–1Mn alloy. X-ray diffraction patterns demonstrated that phase components of the experimental alloys consisted of the α-Mg matrix and Mn precipitates. Optical microscopy images indicated a significant increase in average grain size of the alloys as the extrusion temperature increasing from 250 °C to 400 °C. Scanning electron microscopy graphics revealed that coarsened particles identified as Mn precipitates by EDS were observed within the matrix when extrusion temperature reached 400 °C. Inverse pole figure maps of the experimental samples subjected to different extrusion temperatures in the present work exhibited the typical basal texture, suggesting that basal slip was activated hardly during the tensile stress applied along the extrusion direction. Consequently, extrusion temperature displayed the significant impact on microstructure, texture, and mechanical properties of as-extruded Mg–1Mn alloy. The alloy extruded at both 250 °C and 300 °C exhibited the strong basal texture and refined microstructure with spheroidal nanoscale precipitates dispersing within the matrix and along the grain boundaries, which contributed to their excellent comprehensive mechanical properties. The alloy extruded at 400 °C possessed the typical basal texture and coarsened microstructure, leading to the extremely poor mechanical properties. Simultaneously, the constitutive model of the Arrhenius equation based on Zener-Hollomon parameters was also established in the present investigation. Therefore, optimizing the extrusion temperature to regulate the microstructure, grain orientation distribution, and morphology of precipitates was considered as one of the effective approaches for achieving the excellent mechanical properties of Mg alloys.

Microstructures and Mechanical Properties of the Ultrafine-Grained Mg–3Al–Zn Alloys Fabricated by Powder Metallurgy

Microstructure Evolution and Properties of Mg-9Gd-0.8Al Alloy with Lamellar Phase During Extrusion at Different Temperatures

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

Microstructural evolution and mechanical properties of an ultrahigh-strength Al−Zn−Mg−Cu alloy via powder metallurgy and hot extrusion

Microstructures and Mechanical Properties of a High-Strength Mg-3.5Sm-0.6Zn-0.5Zr Alloy

Microstructure and mechanical properties of Mg-Gd-Zn-Zr alloy after hot extrusion

Microstructure and Properties of AZ61 Ultra-Fine Grained Magnesium Alloy Prepared by Mechanical Milling and Powder Metallurgy Processing

Unveiling the microstructure evolution and deformation mechanisms of micro-alloying Mg-1.5Zn-0.5Zr-0.5Sr alloy via extrusion-shearing

Microstructure and Mechanical Properties at Elevated Temperature of Powder Metallurgy Al-Zn-Mg-Cu Alloy Subjected to Hot Extrusion

Effect of extrusion temperature on microstructure, mechanical properties, and deformation mechanism of Mg-2.5Er-0.6Zr alloy

Microstructure and tensile properties of a low-alloyed magnesium alloy: effect of extrusion temperature

Microstructure evolution, strengthening mechanisms and deformation behavior of high-ductility Mg−3Zn−1Y−1Mn alloy at different extrusion temperatures

On Mechanical Properties and Superplasticity of Mg–15Al–1Zn Alloys Processed by Reciprocating Extrusion

Deformation behaviour, microstructure evolution and dynamic recrystallization mechanism of AZ31 magnesium alloy under co-extruded by Mg-Al composite billet

Effect of Hot Extrusion on Microstructure, Texture, and Mechanical Properties of Mg-Zn-Mn-0.5Ca Alloy

Effects of extrusion process on microstructure, precipitates and mechanical properties of Mg-Gd-Y-Zr-Ag alloys

Hot Extrusion Effect on the Microstructure and Mechanical Properties of a Mg–Y–Nd–Zr Alloy

Realizing ultra-fine grains and ultra-high strength in conventionally extruded Mg-Ca-Al-Zn-Mn alloys: The multiple roles of nano-precipitations

Development of ultrahigh-strength low-alloy Mg-0.7Al-0.3Ca-0.4Mn (wt.%) alloy with excellent ductility via controlling extrusion temperature

Hot deformation behavior and extrusion temperature-dependent microstructure, texture and mechanical properties of Mg–1Mn alloy

Ultra-high strength Al-Zn-Mg-Cu alloys with high zinc content prepared via powder hot extrusion