Abstract:This work fabricated a series of microstructures consisting of different equiaxed α (α eq ) and β phase contents to investigated the effect of phase content on mechanical properties and deformation mechanism, including slip initiation, slip transfer, stress-induced martensite (SIM) and crack nucleation of TC21 titanium alloy. The results show that, with the decrease of α eq phase content, the YS of the alloy firstly decreases and then increases, the UTS gradually increases, and the EL gradually decreases. The significant variation of mechanical properties is closely related to the deformation mechanism of microstructures with different α eq phase contents. In sample with high α eq phase content, α eq phase is deformed by slip prior to β phase, and with the increase of strain, β phase can coordinate deformation by slip initiation and exhibits a better ability to coordinate plastic deformation. In samples with medium α eq phase content, the stability of β phase decreases, slip in α eq grain and SIM in β grain can be initiated simultaneously. However, the formation of SIM would harden β phase, and with the increase of strain, it would restrain the ability of β phase to further coordinate plastic deformation. In samples with low α eq phase content, the stability of β phase decreases sharply, which could induce the precipitation of fine-lamellar secondary α (α s ) and acicular martensite α'' in β grain during annealing. These precipitated α s and α'' can not only inhibit the formation of SIM, but also dramatically reduce the ability of β phase to coordinate plastic deformation. Meanwhile, the evolution of deformation mechanism in different samples can significantly influence the crack nucleation location (slip band or α eq /β interface) during deformation. This paper analyzes in detail the effect of α eq phase content on mechanical properties of TC21 titanium alloy based on deformation mechanism, it would contribute to the establishment of a relationship among phase content, deformation mechanism and mechanical properties.

Effect of Α Phase on Fatigue Crack Growth of Ti-6242 Alloy

Effects of Tensile/compressive Overloads on Fatigue Crack Growth Behavior of an Extra-Low-interstitial Titanium Alloy

Microstructural effects on the high-cycle fatigue and fracture behaviors of Ti-6Al-4V alloy

Hot Deformation Behavior of a Novel Near-β Titanium Alloy Ti-5.5Mo-6V-7Cr-4Al-2Sn-1Fe in (α+β) Phase Region

Fatigue Crack Growth Behavior of Beta-Annealed Ti–6Al–2Sn–4Zr–xMo (x = 2, 4 and 6) Alloys: Influence of Microstructure and Stress Ratio

In-situ Investigation Via High Energy X-ray Diffraction of Stress-Induced(0002)α→(110)β Transformation in a Ti-5.5Mo-7.2Al-4.5Zr-2.6Sn-2.1Cr Alloy

The Effect of Precursory Α and Ω Phase on Microstructure Evolution and Tensile Properties of Metastable Β Titanium Alloy

Preparation of Multiscale α Phase by Heat Treatments and Its Effect on Tensile Properties in Metastable β Titanium Alloy Sheet

Effect of phase content on mechanical properties and deformation mechanism in TC21 titanium alloy: An in-situ tensile investigation

The role of the ω phase on the microstructure evolution of precipitation and mechanical property in Ti-3Al-5Mo-4Cr-2Zr-1Fe

Investigation on Fatigue Threshold Testing Methods in a Near Lamellar TiAl Alloy

Phase Interface-Induced Dwell Fatigue Cracks in Titanium Alloy with Lamellar Microstructure

TEM analysis of quasi in-situ formed tensile and fatigue cracks in a dual-phase Ti alloy

The Effect of Phase Angle on the Thermo-Mechanical Fatigue Life of a Titanium Metal Matrix Composite

Microstructure stability and damage mechanisms in an α/β Ti-6Al-4V-0.55Fe alloy during low cycle dwell-fatigue at room temperature

Effect of High Strain Rate on Adiabatic Shearing of α+β Dual-Phase Ti Alloy

Effect of Annealing Temperature on As-Cast Ti6Al4V–5Cu Alloy Microstructure, Tensile Properties, and Fracture Toughness

Investigation of α phase evolution and tensile fracture behavior of Ti5Al2Sn2Zr4Mo4Cr alloy fabricated by directed energy deposition

Thermo-mechanical fatigue crack growth in a nickel-based powder metallurgy superalloy

Phase Composition Effects on Dynamic Behavior and Strain Rate Sensitivity in Metastable β-Ti Alloys

Effects of the cooling rate on mechanical properties and microstructure of near- α Ti-6Al-3Zr-2Nb-Mo alloy