Abstract:This article is devoted to the experimental study of tuning method for an Alvarez-type drift tube linac (DTL) of the Compact Pulse Hadron Source (CPHS) project at Tsinghua University. The biperiodic structure based on the post couplers are introduced to overcome the instability of the Alvarez DTL tank which is used to operate in 0 (or 2π) mode. The experimental method and results are presented, and the tuning scheme for the formal CPHS DTL is summarized from the tuning experiment. INTRODUCTION The effective shunt impedance of the Alvarez-type DTL is typically high when it operates in a typical 0 (or 2π) mode with the group velocity of 0. But the structure is very susceptible to perturbation such as the beam loading, mechanical and installation error, because of the narrow space near the adjacent modes on the TM dispersion curve. The post couplers, which are the resonant-coupling elements constitutionally, are mounted on the wall of the DTL cavity oppositely and alternatively to introduce a new PCs (post couplers) dispersion curve. When the stopband between the two passbands of the dispersion curves disappears by adjusting the slugging length of the post couplers, the lowest frequency of the TM passband will be moved to the π/2 mode point of the new dispersion curve. Therefore the new stable biperiodic structure of the DTL will be achieved [1]. To verify the tuning method, one model cavity has been machined and the turning experiment is carried out based on the cavity. The cavity is designed and manufactured for verifying the mechanical design and undertaking some low-power experiment. The model cavity consists of ten full drift tubes, two half drift tubes mounted on the end flanges, three post couplers and two tuners [2]. The end of the post couplers is designed to be eccentric to facilitate the tuning of the local field distribution by rotating the post. TUNING EXPERIMENTAL CONFIGURATION On the experimental stand as shown in Fig. 1, the measurement based on the bead-pull method is executed. According to the perturbation theory, when the bead is pulled into the field between the two adjacent drift tubes, the resonant frequency changes. Then the corresponding phase shift can be detected by a vector network analyzer (VNA) and the electric field along the beam-axis can be deduced [3]. Figure: 1 Tuning experimental stand. A stepping motor is adopted to pull a fine nylon line on which the small perturbation bead is fixed. The size of the bead shall be rather appropriate, so that the responsive signal caused by the bead is big enough compared with the background noise and at the same time within the linear range of the phase around the resonant frequency. It depends on the Q factor of the cavity. The Q factor of this model cavity is measured as 17796 which is about 44% of the designed value. It is because that the surfaces of the interior copper-plated cavity wall and the aluminous end flanges are oxidic. With the value of the Q factor, the radius of the bead is determined as 0.7 mm by estimation. To ensure the accuracy of the measurement, the peak field is employed to represent the field distribution instead of the integral one due to its further advantages [4]. Before the measurement, the reproducibility is checked. The reproducibility Rij is defined by Eq. (1).

Design of a L-band Cavity Optimized for Robinson Instability in the TTX-II Storage Ring

Lattice Design and Beam Dynamics of a Storage Ring for a Thomson Scattering X-Ray Source

Study of Robinson Instabilities with A Higher-Harmonic Cavity for the Hls Phase Ii Project

Analysis of Coupled-Bunch Instabilities for the NSLS-II Storage Ring with a 500MHz 7-Cell PETRA-III Cavity

DESIGN OF A COMPACT STORAGE RING FOR THE TTX

Analytic modeling of instabilities driven by higher-order modes in HLS II RF system with a higher-harmonic cavity

Robinson Instability of a Double-bunch System

Design and Optimization of a Longitudinal Feedback Kicker Cavity for the HLS-II Storage Ring

Laser electron storage ring for ttx∗

Broadband Impedance Calculations and Single Bunch Instabilities Estimations of of the HLS-II Storage Ring

Design of the Beam Transport Line and Injection System of the Compact Storage Ring for TTX

Design of A 4.8-M Ring for Inverse Compton Scattering X-Ray Source

Analysis of Beam Break Up Instability in an S-band Irradiation Travelling-Wave Linac

Development of a 166.6 MHz β = 1 higher-order-mode-damped superconducting cavity

Experimental Study of Tuning Method on a Model Alvarez DTL Cavity for CPHS Project

Design, fabrication and test of a taper-type half-wave superconducting cavity with the optimal beta of 0.15 at IMP

Beam Stability Analysis of the PLS-II Storage Ring for Taper Shape Change of the Superconducting RF Cavities

Calculations for Shortening the Bunch Length in Storage Rings Using A Harmonic Cavity

Superconducting RF Deflecting Cavity Design and Prototype for Short X-ray Pulse Generation

Study and Design of the Coupled Cavity with Ladder RFQ and IH DTL Structure for Transportable Neutron Source

Tuning control system of a third harmonic superconducting cavity in the Shanghai Synchrotron Radiation Facility