Abstract:In the present study, the effects of various Sn and Ca equal proportional addition (0.3:0.1, 0.6:0.2, 1.2:0.4, wt%) on the microstructure, mechanical properties and corrosion behavior of Mg-Sn-Ca alloys were systematically investigated. With the increase of Sn and Ca content, microstructure uniformity of the Mg-Sn-Ca alloy was improved, the average grain size was refined (from 34.4 μm to 21.62 μm, 13.47 μm), and more CaMgSn phases were generated (from 0.39 % to 1.64 %, 4.53 %). With increasing Sn and Ca content, the tensile yield strength (TYS) and ultimate tensile strength (UTS) of Mg-Sn-Ca alloys were gradually increased (TYS: from 91.8 MPa to 98.24 and 125.05 MPa; UTS: from 187.48 MPa to 190.73 and 214.58 MPa), mainly due to the contribution of grain refinement. The electrochemical tests revealed that the corrosion resistance of the Mg-Sn-Ca alloy initially decreases and then increases with the increase of Sn and Ca contents. The hydrogen evolution volume of Mg-0.3Sn-0.1Ca alloy was 41.91 mL cm−2, and the corrosion current density was −1.54 × 10−3 A/cm2. As for Mg-0.6Sn-0.2Ca alloy, deteriorated corrosion resistance compared to the Mg-0.3Sn-0.1Ca alloy was mainly ascribed to the micro-galvanic corrosion between the CaMgSn phase and Mg-matrix. The Mg-1.2Sn-0.4Ca alloy had the best corrosion resistance, with the lowest hydrogen evolution volume of 34.09 mL cm−2 and a minimum current density of −1.15×10−3 mA cm−2, its high corrosion resistance could be attributed to the grain refinement and homogenous distributed CaMgSn phase and more generated Ca(OH)2 product film with dense-structure.

Microstructure, Tensile Properties, and Corrosion Behavior of Die-Cast Mg-7Al-1Ca- X Sn Alloys

Effect of Sn Addition on Microstructure and Corrosion Behavior of As-Extruded Mg–5Zn–4Al Alloy

Effects of Sn Content on the Microstructure and Mechanical Properties of Mg–7Zn–5Al Based Alloys

Effect of Sn Addition on the Microstructure and Corrosion Behavior of Dilute Wrought Mg-Zn-Ca Series Alloys

Microstructure and Tensile Properties of the Mg-6Zn-4Al-xSn Die Cast Magnesium Alloy

Microstructure, Mechanical Properties and First Principle Calculation of Mg-7Al (-2Sn) Alloys Prepared by Vacuum Die-casting

Enhanced Mechanical Properties and Isotropy of Mg-2Al-0.8Sn Alloy through Ca Addition

Effects of Sn Addition on Microstructure and Mechanical Properties of Mg-Zn-Al Alloys

Microstructure and Mechanical Behavior of Mg-0.5Si-xSn Alloys

Influence of Al Addition on the Microstructure and Mechanical Properties of Mg-Zn-Sn-Mn-Ca Alloys

Microstructure, Mechanical Properties and First-Principle Analysis of Vacuum Die-Cast Mg–7Al Alloy with Sn Addition

Effect of Sn Addition on the Microstructure and Mechanical Properties of Mg–6Zn–1Mn (wt.%) Alloy

The effect of various Sn and Ca equal proportional addition on the microstructure, mechanical behavior and corrosion performance of Mg alloys

Solidification Microstructure and Mechanical Properties of Cast Magnesium-Aluminum-Tin Alloys

Effects of Sn Addition on As-Cast Microstructure and Mechanical Properties of Mg-3.8zn-2.2ca Magnesium Alloy

Microstructure And Mechanical Properties Of Mg-5sn-5zn-Xca Alloys

Improving the Mechanical Properties and Intergranular Corrosion Resistance of Al-9.2Mg-0.8Mn-0.2Zr Alloy by Sn Addition

Effect of Sn content on microstructure and tensile properties of as-cast and as-extruded Mg−8Li−3Al−(1,2,3)Sn alloys

Effect of Mischmetal Addition on Microstructure and Mechanical Properties of As-Cast and As-Rolled Mg–Sn–Ca Alloys

Influence of Ca Addition on Microstructure, Mechanical Properties and Corrosion Behavior of Mg-2Zn Alloy

Microstructure, Mechanical, and Corrosion Properties of Extruded Low-Alloyed Mg-xZn-0.2Ca Alloys