Abstract:An Mg-3Al-1Zn-xSn (x = 0, 3, 6, 9) alloy was prepared by die-casting and analyzed by XRD, SEM, and EBSD. The microstructure, second phase, and grain orientation of the AZT31x alloy were characterized. As the Sn content increased from 3 wt.% to 9 wt.%, the tensile and yield strength of the alloy were effectively improved. With the addition of Sn, the grain size of alloys decreases gradually blocking the dislocation by the grain boundary and the dispersion of the Mg2Sn second phase in the AZT31x(x = 3, 6, 9) alloys contributes to the strength via grain boundary pinning. According to theoretical analysis and calculation, the high strength of AZT319 alloy is partly attributed to the grain fine strengthening (sigma HP = 13.76 Mpa) and second phase strengthening (Delta sigma = 9.27 similar to 12.67 MPa). The total increased strengthening value is lower than experimental value (Delta sigma = 31.82 MPa). The ratio about tau(prism)/tau(basal) and tau(< c+a >)/tau(basal) in die-cast alloys tensioned to 0.08 deformation gradually decrease, which can reflect that high-Sn content contributes to the strain hardening behavior. The ductility of AZT313 alloy was lightly improved due to the {10-12} tensile twins. When excessive Sn was added, the Mg2Sn second phase coarsened and acted as the nucleus of micro-cracks during the stretching process, thereby reducing the ductility of the alloy.

Effect of Sn Addition on the Microstructure and Mechanical Properties of Mg–6Zn–1Mn (wt.%) Alloy

Effects of Sn Addition on the Microstructures and Mechanical Properties of Mg-6Zn-3Cu- X Sn Magnesium Alloys

Effects of Sn Content on the Microstructure and Mechanical Properties of Mg–7Zn–5Al Based Alloys

Effects of Sn Addition on Microstructure and Mechanical Properties of Mg-Zn-Al Alloys

Microstructure Evolution and Mechanical Properties of ZM81-xSn Wrought Magnesium Alloys

Microstructure and Tensile Properties of the Mg-6Zn-4Al-xSn Die Cast Magnesium Alloy

Effects of Zn Addition on Microstructure and Mechanical Properties of Mg-8AI-2Sn Alloy

Effects of Mn Addition on the Microstructure and Mechanical Properties of Cast Mg–9Al–2Sn (wt.%) Alloy

Microstructure and Tensile Properties of As Extruded and As Aged Mg–Al–Zn–Mn–Sn Alloy

Improvement of mechanical properties of hot extruded and age treated Mg–Zn–Mn–Ca alloy through Sn addition

Effects of Sn on microstructure and mechanical properties of ZM61 alloy

Effects of Zn Addition on Microstructure and Mechanical Properties of Mg-8Al-2Sn Alloy

Effects of Mn Addition on the Microstructures, Mechanical Properties and Work-Hardening of Mg-1Sn Alloy

Effect of Sn content on microstructure and tensile properties of as-cast and as-extruded Mg−8Li−3Al−(1,2,3)Sn alloys

Effect of Zn Content on the Microstructure and Mechanical Properties of Mg–Al–Sn–Mn Alloys

Effects of Sn Addition on As-Cast Microstructure and Mechanical Properties of Mg-3.8zn-2.2ca Magnesium Alloy

The Effect of Sn Addition on Aging Behavior and Mechanical Properties of Wrought AZ80 Magnesium Alloy

Effect of Sn Addition on the Microstructure and Mechanical Properties of AZ31 Alloys

Effect of Al on the Microstructure and Mechanical Properties of Mg–6Zn–2Sn–0.5Mn Alloy

Effects of Zn Addition on the Aging Behavior and Mechanical Properties of Mg-8Al-2Sn Wrought Alloy

Effects of Sn and Mn Addition on the Microstructure and Mechanical Properties of As-Extruded Mg–2Al–1Zn Alloys