Abstract:Pure magnesium (Mg) develops a strong basal texture after conventional processing of hot rolling or extrusion. Consequently, it exhibits anisotropic mechanical properties and is difficult to form at room temperature. Adding appropriate alloying elements can weaken the basal texture or even change it, but the improvement in formability and mechanical properties is still far from expectations. Over the past 20 years, considerable efforts have been made and significant progress has been made on wrought Mg alloys at the fundamental and technological levels. At the fundamental level, textures formed in sheets and extrusions of different alloy compositions and produced under different strain paths or thermomechanical processing conditions are relatively well established, with the assistance of the advanced characterization technique of electron backscatter diffraction. At the technological level, room temperature formability of sheet has been significantly improved, and tension–compression yield asymmetry of extrusion is also remarkably reduced or eliminated. This paper starts with an overview of dislocations, stacking faults and twins, and deformation of single crystals of pure Mg along different orientations and under different loading conditions, followed by a review of microstructure (texture and grain size) and deformation of polycrystalline pure Mg with different textures, grain sizes, and loading conditions. With this information as a base, texture, grain size, and deformation of polycrystalline Mg alloy sheets and extrusions produced under different processing conditions are systematically examined and compared. Remaining and emerging scientific and technology issues are then highlighted and discussed in the context of texture and grain size. The need for better-resolution diffraction and spectroscopy techniques is also discussed in the relationship between texture change and grain boundary solute segregation.

Tension–Compression Asymmetry Improved by Cold Extrusion in Pure Magnesium

Improved Tension/compression Asymmetry Achieved in High-Strength Magnesium Alloys Via Compression-Extrusion Process

Microstructures and Mechanical Properties of Pure Magnesium Bars by High Ratio Extrusion and Its Subsequent Annealing Treatment

Tension-compression Asymmetry of Extruded Mg-Gd-Y-Zr Alloy with a Bimodal Microstructure Studied by In-Situ Synchrotron Diffraction

Formation of Gradient Microstructure and Elimination of Tension-Compression Yield Asymmetry of the Extruded Mg-4.58Zn-2.6Gd-0.18Zr Alloy Via Free-End Torsion

Mechanical anisotropy improvement in ultrafine-grained ZK61 magnesium alloy rods fabricated by cyclic extrusion and compression

Achieving Improved/Reversed Tension–Compression Asymmetry by Tailoring Extrusion Processing for Mg–Sn(–Y) Alloy

Microstructure and texture evolution during compression-extrusion process for tension/compression symmetrical ZK61 magnesium alloy rod

Evolution of Microstructure and Tensile Properties of Extruded Mg-4Zn-1Y Alloy

Ex-situ EBSD Analysis of Yield Asymmetry, Texture and Twinning Development in Mg–5Li–3Al–2Zn Alloy During Tensile and Compressive Deformation

The Improved Tension-Compression Asymmetry with Double-Extrusion for Mg-Sn-(Y) Alloys

Improving the Microstructure and Mechanical Properties of Magnesium-Alloy Sheets with a New Extrusion Method

The improvement of grain refinement, texture modification and mechanical properties of pure Mg prepared by cyclic expansion extrusion with an asymmetric extrusion cavity

Microstructure, Texture, and Enhanced Mechanical Properties of an Extruded Mg–rare Earth Alloy after Hot Compression

Microstructure and Mechanical Properties of Extruded Mg-Zn-Y Alloy

Development of Mechanical Properties in AZ31 Magnesium Alloy Processed by Cold Dynamic Extrusion

Microstructure, Deformation, and Property of Wrought Magnesium Alloys

Asymmetric Tension-Compression Mechanical Behaviors of Extruded Mg-4.58Zn-2.6Gd-0.18Zr Alloy with Double-Peak Fiber Texture

Reduced Yield Asymmetry and Excellent Strength-Ductility Synergy in Mg-Y-Sm-Zn-Zr Alloy Via Ultra-Grain Refinement Using Simple Hot Extrusion

Fine-grained Structure and Recrystallization at Ambient Temperature for Pure Magnesium Subjected to Large Cold Plastic Deformation

Asymmetric Extrusion Technology of Mg Alloy: A Review