Abstract:The dense WC-M2 high-speed steel matrix composites (WC-M2 HSS MMCs) with different WC content were prepared by mechanical alloying and vacuum sintering process. Tungsten Carbide (WC) with 0, 2, 5, 8, and 10 (by weight %) were dispersed in the matrix. The effects of WC content on the densification mechanism, phase composition, microstructure, fracture morphology, and mechanical and wear properties of the sintered composites were systematically investigated. The experimental results showed that at a vacuum sintering temperature of 1260 °C, the composite material specimens achieved near-full densification, with predominant phases being Martensitic, M 7 C 3 , M 6 C, M 2 C, MC, WC, α-Fe, and γ-Fe. Reasonable WC addition has improved grain uniformity and reduced micro-defects, which enhanced the overall mechanical properties. With an increase in WC content, the hardness and relative density of the composites showed a gradual increase, whereas transverse rupture strength and impact toughness initially improved but subsequently decreased. The friction coefficient displayed an initial increase followed by a decrease, while the wear rate showed an opposite trend. The impact fracture morphology is dominated by the interfacial separation between the WC particle phase and the binder phase, supplemented by the plastic tearing of the binder phase. The impact toughness mainly depended on the fracture of the binder phase. During crack propagation, both intergranular and transgranular fractures exist, of which the intergranular fracture prevails and coarse grains are more prone to transgranular fracture. With 5 wt.% WC, the steel matrix composites obtained peak mechanical performance, with impact toughness, bending strength, and hardness measuring 13.2 J cm −2 , 1584.3 MPa, and 780.9 HV, respectively, which also yielded the highest wear resistance.

Effects of Ni60WC25 Powder Content on the Microstructure and Wear Properties of WC P Reinforced Surface Metal Matrix Composites

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

Effects of WC on Structure and Properties of Spark Plasma Sintered Al0.2CoCrFeNi Alloy

Effects of Ni on the Microstructures and Properties of WC–6Co Cemented Carbides Fabricated by WC–6(Co, Ni) Composite Powders

Effect of Surface-Modified WC/W2CP on Wear Behavior of WC/W2CP-NiCrBSi/Refractory Steel Composite

Study on Manufacturing and Wear Resistance of WC Reinforced Fe-2Cu-2Ni-1Mo-1C Powder Metallurgy Steel

Effect of WC mass fraction on the microstructure and frictional wear properties of WC/Fe matrix composites

Effect of Ni Content on Microstructure and Properties of WC-Ni Composites Prepared by Electroless Plating and Powder Metallurgy

Effect of WC Incorporation on the Microstructure and Mechanical Properties of Ni625/WC Spark Plasma Sintered Composites

Study on Effect of High-Entropy Alloy Binder on Microstructure and Properties of WC Cemented Carbide Doped with Rare Earth Oxide

Effect of Cr Addition on the Microstructure and Abrasive Wear Resistance of WC-reinforced Iron Matrix Surface Composites

Effect of Powders Recycling on Microstructure Evolution and Wear Mechanism of Plasma Sprayed Ni625-WC Composite Coating

Influence of WC content on the wear resistance of plasma sprayed WC/Ni60 coatings

Effects of Metal Binder Content and Carbide Grain Size on the Microstructure and Properties of SPS Manufactured WC–Fe Composites

Effect of Tungsten Carbide Additions on the Microstructure, Mechanical, and Tribological Properties of M2 High-Speed Steel Matrix Composites

Microstructure and Wear Performance of WC Reinforced Ni-based Composite Coating

Effect of W-to-C Atomic Ratio on Microstructure and Performance of In-Situ WC/Fe Composite Prepared by Spark Plasma Sintering

Interface microstructure and abrasive wear properties of WC-iron matrix composites with Ni, Mo, Fe added to the preforms

Effect of WC Content on Microstructures and Mechanical Properties of FeCoCrNi High-Entropy Alloy/wc Composite Coatings by Plasma Cladding

Microstructural and Mechanical Characterization of Colloidal Processed WC/(W5Vol%Ni) via Spark Plasma Sintering

Dissolving Mechanism of the WC/W2Cp in NiCrBSi Alloy and Surface Modification for the WC/W2Cp by Carburizing