Abstract:Superior properties of titanium alloy Ti-6Al-4V over many other materials like higher strength to weight ratio, ability to maintain strength at elevated temperatures (around 500 degrees C) and ability to resist against corrosion in severe environmental conditions have made them as an excellent choice for using them in many aerospace and biomedical industrial applications. But the properties which had made them an ideal choice for most practical applications severely hinders their machinability and therefore is renowned as difficult to machine material. The low thermal conductivity of titanium alloys does not allow the generated heat to dissipate away quickly and thus results in chemical reaction with cutting tool materials at higher temperatures. Several researchers have tried to reduce tool-chip interface temperature, increase tool life and surface quality with carbide tools by applying different cutting fluids like water based emulsions flood cooling, oil flood coolant, minimum quantity lubrication MQL and various liquid nitrogen LiN cryogenic cooling techniques and has found some advantages of MQL & LiN cooling in terms of not only in improved surface roughness & tool life but also in controlling the hazardous environmental impact by eliminating the use of hazardous and expensive traditional flood coolant equipment. Moreover the thrust for higher quality and productivity has directed the attention of researchers on using super hard cutting tool materials for machining of titanium alloys. Super hard cutting tool like polycrystalline diamond PCD, Poly Cubic Boron Nitride PCBN and Binderless CBN inspite of their higher cost has many advantages over carbide tools like higher thermal conductivity, lower wear rate and high hot strength. Studies have shown that PCD tools can give better tool life and surface roughness as compared to carbide and PCBN tools. The studies on evaluating the effectiveness of PCD insert in high speed end milling of titanium alloy has not yet considered the effect of different types of cooling strategies. Therefore there is need to study the effectiveness of PCD tools in various wet cutting conditions and find optimal coolant which can help to increase tool life and can provide better surface quality and therefore this study is specifically designed to address above mentioned issues. Four different type of coolants "water based flood cooling, oil based flood coolant, MQL and LIN cryogenic cooling technique has been applied and their effect on tool-chip interface temperature, tool edge temperature, cutting forces and stresses acting on tool edge are observed using Finite element, FE numerical simulations. FE numerical simulations are widely employed in academic research field because it provides fast & reliable results and thus eliminates expensive experimentation costs which otherwise is always required. Results have shown that the LiN cooling technique has shown clear advantages over MQL and flood coolant techniques in terms of temperature near the tool rake face and in reducing cutting forces and stresses acting on cutting edge. Therefore from the study it can be concluded that LiN cooling can be used for machining of titanium alloys with PCD inserts for getting maximum productivity and part quality.

Machining Performance and Tool Wear Analysis on Cryogenic Treated Insert During End Milling of Ti-6Al-4V Alloy

Performance Analysis of TiAlSiN Coated Tungsten Carbide End Milling Tool Subjected to Shallow and Deep Cryogenic Treatments

Tool Wear Behavior of Thermal-Mechanical Effect for Milling Ti-6Al-4V Alloy in Cryogenic

Evaluation of the performance of coated carbide tools in face milling TC6 alloy under dry condition

A New Cutting Tool Design for Cryogenic Machining of Ti–6Al–4V Titanium Alloy

Effects of cooling air temperature on cryogenic machining of Ti–6Al–4V alloy

Evaluating the Effectiveness of PCD Tools on Machinability of Titanium Alloy Ti-6Al-4V in High Speed End Milling under Various Wet Cutting Conditions

Experimental Investigation on Tool Wear Characteristics of PVD and CVD Coatings During Face Milling of Ti6242S and Ti-555 Titanium Alloys

Experimental investigations on performance of TiN and TiAlN coated tools in cryogenic milling of AISI D2 hardened steel

Tool Wear and Surface Integrity of γ-TiAl Cryogenic Coolant Machining at Various Cutting Speed Levels

Cutting Performance of Different Coated Micro End Mills in Machining of Ti-6Al-4V

An Experimental and Numerical Approach to Study the Performance of Modified Perforated Cutting Tools on Machining of Ti–6Al–4V Alloy

Tough-brittle transition mechanism and specific cutting energy analysis during cryogenic machining of Ti–6Al–4V alloy

Influence of Microstructure and Hardness on Machinability of Heat-Treated Titanium Alloy Ti-6Al-4V in End Milling with Polycrystalline Diamond Tools

Comparative experimental study on application feasibiility of MTCVD TiCN-Al2O3-TiOCN multi-layer coated carbide and PVD TiN single layer coated composite ceramic inserts during dry machining of Ti-6Al-4V

Machining Performance Of Tialn-Coated Cemented Carbide Tools With Chip Groove In Machining Titanium Alloy Ti-6al-0.6cr-0.4fe-0.4si-0.01b

Enhancing Tool Performance in High-Speed End Milling of Ti-6Al-4V Alloy: The Role of AlCrN PVD Coatings and Resistance to Chipping Wear

Comparison of Surface Morphology and Tool Wear in the Machining of Ti-6Al-4V Alloys with Uncoated and TiAlN Tools under Dry, Minimum Quantity Lubrication, Flood Cooling, and Low-Temperature Spray Jet Cooling Conditions

Effect of Cryo-Treated Cutting Tool End Milling on Custom 450 Stainless Steel

WEAR MECHANISMS AND PERFORMANCE OF COATED INSERTS DURING FACE MILLING OFTC11ANDTC17ALLOYS

Machinability Investigations in Cryogenic Internal Cooling Turning Ti-6Al-2Zr-1Mo-1 V Titanium Alloy