Abstract:Superior properties of titanium alloy Ti-6Al-4V over many other materials like higher strength to weight ratio, ability to maintain strength at elevated temperatures (around 500 degrees C) and ability to resist against corrosion in severe environmental conditions have made them as an excellent choice for using them in many aerospace and biomedical industrial applications. But the properties which had made them an ideal choice for most practical applications severely hinders their machinability and therefore is renowned as difficult to machine material. The low thermal conductivity of titanium alloys does not allow the generated heat to dissipate away quickly and thus results in chemical reaction with cutting tool materials at higher temperatures. Several researchers have tried to reduce tool-chip interface temperature, increase tool life and surface quality with carbide tools by applying different cutting fluids like water based emulsions flood cooling, oil flood coolant, minimum quantity lubrication MQL and various liquid nitrogen LiN cryogenic cooling techniques and has found some advantages of MQL & LiN cooling in terms of not only in improved surface roughness & tool life but also in controlling the hazardous environmental impact by eliminating the use of hazardous and expensive traditional flood coolant equipment. Moreover the thrust for higher quality and productivity has directed the attention of researchers on using super hard cutting tool materials for machining of titanium alloys. Super hard cutting tool like polycrystalline diamond PCD, Poly Cubic Boron Nitride PCBN and Binderless CBN inspite of their higher cost has many advantages over carbide tools like higher thermal conductivity, lower wear rate and high hot strength. Studies have shown that PCD tools can give better tool life and surface roughness as compared to carbide and PCBN tools. The studies on evaluating the effectiveness of PCD insert in high speed end milling of titanium alloy has not yet considered the effect of different types of cooling strategies. Therefore there is need to study the effectiveness of PCD tools in various wet cutting conditions and find optimal coolant which can help to increase tool life and can provide better surface quality and therefore this study is specifically designed to address above mentioned issues. Four different type of coolants "water based flood cooling, oil based flood coolant, MQL and LIN cryogenic cooling technique has been applied and their effect on tool-chip interface temperature, tool edge temperature, cutting forces and stresses acting on tool edge are observed using Finite element, FE numerical simulations. FE numerical simulations are widely employed in academic research field because it provides fast & reliable results and thus eliminates expensive experimentation costs which otherwise is always required. Results have shown that the LiN cooling technique has shown clear advantages over MQL and flood coolant techniques in terms of temperature near the tool rake face and in reducing cutting forces and stresses acting on cutting edge. Therefore from the study it can be concluded that LiN cooling can be used for machining of titanium alloys with PCD inserts for getting maximum productivity and part quality.

Experimental investigations on performance of TiN and TiAlN coated tools in cryogenic milling of AISI D2 hardened steel

Performance Analysis of TiAlSiN Coated Tungsten Carbide End Milling Tool Subjected to Shallow and Deep Cryogenic Treatments

Heat Transfer Efficiency of Cryogenic-LN2 and CO2-snow and their application in the Turning of Ti-6AL-4V

Tool Wear and Surface Integrity of γ-TiAl Cryogenic Coolant Machining at Various Cutting Speed Levels

A New Cutting Tool Design for Cryogenic Machining of Ti–6Al–4V Titanium Alloy

Wear Mechanism of Multilayer Coated Carbide Cutting Tool in the Milling Process of AISI 4340 under Cryogenic Environment

Experimental investigation of uncoated, single layer, and multilayer-coated TiAlN/TiN tool inserts in dry orthogonal cutting of AISI/SAE 4140 alloy steel

A sustainable approach in deep hole drilling of Ti6Al4V: Effect of cryogenic cooling on hole parameters and its evaluation

Experiment and numerical study of chip formation mechanism during cryogenic machining of Ti-6Al-4V alloy

On Coolant Flow Rate-Cutting Speed Trade-Off for Sustainability in Cryogenic Milling of Ti–6Al–4V

Tool wear and surface integrity in liquid nitrogen clean cutting of cobalt-based superalloy GH605 with AlTiN coated tools

Tool wear patterns and their promoting mechanisms in hybrid cooling assisted machining of titanium Ti-3Al-2.5V/grade 9 alloy

Evaluating the Effectiveness of PCD Tools on Machinability of Titanium Alloy Ti-6Al-4V in High Speed End Milling under Various Wet Cutting Conditions

Experimental investigation of ultrasonic vibration-assisted cryogenic minimum quantity lubrication for milling of Ti-6Al-4V and grinding of Zerodur

Sustainable milling of Ti–6Al–4V: A trade-off between energy efficiency, carbon emissions and machining characteristics under MQL and cryogenic environment

Economic analysis of eco-friendly lubrication strategies for the machining of Ti48Al2Cr2Nb aluminide

Simulation Analysis of Ti6Al4V Cutting Under Liquid Nitrogen Cryogenic Cooling

Effect of liquid nitrogen jet impingement angle on machinability of titanium alloy in cryogenic cooling

A State of the Art on Cryogenic Cooling and Its Applications in the Machining of Difficult-to-Machine Alloys

Effect of deep cryogenic processing cycles on surface roughness, dimensional stability and microstructure of high carbon high chromium tool steel for cutting tool and dies applications

Milling performance of cryogenic cooled titanium alloy thin-walled parts based on cantilever sheet