Abstract:Using the cost-effective, renewable and nano-sized of citric acid pretreatment rice husk ash (CRHA) as silicon source, high efficient Li4SiO4 (lithium orthosilicate)-based sorbents (CRHA-Li4SiO4) for high-temperature CO2 capture were prepared through the solid-state reaction at lower temperature (700 degrees C). Two typical raw materials (nano-structured Aerosil and crystalline Quartz powders) were used to synthesize Li4SiO4 sorbents (Aerosil-Li4SiO4 and Quartz-Li4SiO4) for comparison purposes. The phase composition behavior, surface area, and morphology of the silicon sources, heat treated raw materials and as-received Li4SiO4 sorbents were studied by analytical techniques. The CO2 adsorption capacity and adsorption-desorption performance were tested by the thermo-gravimetric analyses (CO2 atmosphere) and a fixed bed reactor, respectively. Compared with the case of its original samples, the morphology of heat treated raw materials had a greater effect on the phase composition, microstructure, special surface area and CO2 adsorption properties of their resulting sorbents. Although the calcined Quartz sample maintained the structure of micron particles, its reactivity was not enough to react completely with Li2CO3. Due to the greater reactivity of nanoparticles, Aerosil-Li4SiO4 presented pure of Li4SiO4 whereas it obtained large particles with dense morphology, which was coming from the pronounced fusing of silica nanoparticles during the calcined process. Conversely, CRHA-Li4SiO4 achieved porous agglomerates of submicron particles resulting from a high anti-sintering character of its calcined CRHA. This more favorable structure of CRHA-Li4SiO4 could lead to the higher CO2 adsorption capacity of 30.5 wt% (6.92 mmol/g Li4SiO4, corresponding to 83.1% efficiency), faster kinetic behavior and better regenerability (its adsorption capacity only decreased 2.1 wt% from the first cycle to the 15th cycle), which was illustrated by the thermogravimetric analyses and fix bed results. (C) 2014 Elsevier Ltd. All rights reserved.

Development of a Fly Ash Derived Li4SiO4-based Sorbent for CO2 Capture at High Temperatures

High Performance of Fly Ash Derived Li 4Sio4-Based Sorbents for High Temperature CO2 Capture

CO2 high-temperature sorbent (Al, Fe, Ti) CO-doped Li4SiO4 from fly ash-derived SiO2 aerogel: In-situ synthesis, enhanced capture ability and long cycle stability

Fly Ash-CaO Sorbents Modified with Chlorides and Hydroxides for CO2 Capture in High-Temperature Flue Gas

Study on Cyclic Carbonation Property of CaO-based Sorbents Modified With Fly Ash

Development of Stabilized Ca-based CO2 Sorbents Supported by Fly Ash

Li4SiO4 Adsorbent Derived from Industrial Biomass Fly Ash for High-Temperature CO2 Capture

Performance of Coal Fly Ash Stabilized, CaO-based Sorbents under Different Carbonation–Calcination Conditions

Fly-Ash-Modified Calcium-Based Sorbents Tailored to Co2 Capture

High-performance Li4SiO4 Sorbents Prepared from Solid Waste for CO2 Capture

Development of One-Step Synthesized SO42−/ZrO2-fly Ash (SZ@FA) Solid Acid Catalysts for Energy-Efficient Sorbent Regeneration in CO2 Capture Processes.

Developing a Novel CaO-Based Sorbent for Promoted CO2 Capture and Tar Reduction

Green Synthesis of Nanosilica from Coal Fly Ash and Its Stabilizing Effect on CaO Sorbents for CO 2 Capture.

Enhanced high temperature cyclic CO2 capture on Li4SiO4 sorbent from two-dimensional SiO2 nanomeshes

Sol-gel Derived, Na/K-doped Li4SiO4-based CO2 Sorbents with Fast Kinetics at High Temperature

Enhancement of Reactivity in Li4SiO4-based Sorbents from the Nano-Sized Rice Husk Ash for High-Temperature CO2 Capture

High temperature capture of CO2 on Li4SiO4‐based sorbents from biomass ashes

The Effect of Fly Ash on Reactivity of Calcium Based Sorbents for CO 2 Capture

Lithium based high temperature sorbent from copper slag: Synthesis and CO 2 capture performance

High-Entropy Fluorite Oxide-Modified CaO-Based Sorbent Pellets for Enhanced High-Temperature CO2 Capture

Efficient carbon dioxide adsorption properties of cellular structure Li 4 SiO 4 sorbents prepared by additive manufacturing based on polymer-derived ceramics strategy