Abstract:The ternary polymerization strategy of incorporating different donor and acceptor units forming terpolymers as photovoltaic materials has been proven advantageous in improving power conversion efficiencies (PCEs) of polymer solar cells (PSCs). Herein, a series of low band gap nonconjugated terpolymer acceptors based on two different fused-ring electron-deficient building blocks (IDIC16 and ITIC) with adjustable photoelectric properties were developed. As the third component, ITIC building blocks with a larger π-conjugation structure, shorter solubilizing side chains, and red-shifted absorption spectrum were incorporated into an IDIC16-based nonconjugated copolymer acceptor PF1-TS4, which built up the terpolymers with two conjugated building blocks linked by flexible thioalkyl chain-thiophene segments. With the increasing ITIC content, terpolymers show gradually broadened absorption spectra and slightly down-shifted lowest unoccupied molecular orbital levels. The active layer based on terpolymer PF1-TS4-60 with a 60% ITIC unit presents more balanced hole and electron mobilities, higher photoluminescence quenching efficiency, and improved morphology compared to those based on PF1-TS4. In all-polymer solar cells (all-PSCs), PF1-TS4-60, matched with a wide band gap polymer donor PM6, achieved a similar open-circuit voltage (Voc) of 0.99 V, a dramatically increased short-circuit current density (Jsc) of 15.30 mA cm–2, and fill factor (FF) of 61.4% compared to PF1-TS4 (Voc = 0.99 V, Jsc = 11.21 mA cm–2, and FF = 55.6%). As a result, the PF1-TS4-60-based all-PSCs achieved a PCE of 9.31%, which is ∼50% higher than the PF1-TS4-based ones (6.17%). The results demonstrate a promising approach to develop high-performance nonconjugated terpolymer acceptors for efficient all-PSCs by means of ternary polymerization using two different A–D–A-structured fused-ring electron-deficient building blocks.This article has not yet been cited by other publications.

Nonfullerene Acceptors with Enhanced Solubility and Ordered Packing for High-Efficiency Polymer Solar Cells

Realizing 19.05% Efficiency Polymer Solar Cells by Progressively Improving Charge Extraction and Suppressing Charge Recombination

Multifunctional Solid Additive Enabling All-Polymer Solar Cells with Improved Efficiency, Photostability and Mechanical Durability

High performance all-polymer solar cells enabled with solvent and solid dual additives

Enhanced Efficiency in Fullerene-Free Polymer Solar Cell by Incorporating Fine-designed Donor and Acceptor Materials.

Additive-induced intermolecular interaction enhancement enables highly efficient organic solar cells

Oligothiophene Additive‐Assisted Morphology Control and Recombination Suppression Enable High‐Performance Organic Solar Cells

Asymmetrified Benzothiadiazole-Based Solid Additives Enable All-Polymer Solar Cells with Efficiency Over 19

Improvement in Power Conversion Efficiency of All-Polymer Solar Cells Enabled by Ultrafast Channels for Charge Dynamics

Near‐Infrared Electron Acceptors with Fluorinated Regioisomeric Backbone for Highly Efficient Polymer Solar Cells

Improving Miscibility of Polymer Donor and Polymer Acceptor by Reducing Chain Entanglement for Realizing 18.64% Efficiency All Polymer Solar Cells

Efficient As‐Cast Polymer Solar Cells with High and Stabilized Fill Factor

Enhanced efficiency in nonfullerene organic solar cells by tuning molecular order and domain characteristics

A Planar Electron Acceptor for Efficient Polymer Solar Cells

Cyclopentadithiophene-cored Non-Fullerene Acceptors for Efficient Polymer Solar Cells with Superior Stability

Solid Additive Tuning Polymer Blend Morphology Enables Non-halogenated-solvent All-polymer Solar Cells with Efficiency over 17%

A Highly Efficient Polymer Non-Fullerene Organic Solar Cell Enhanced by Introducing a Small Molecule As a Crystallizing-Agent

A Double-Cable Y-series-based Polymer Acceptor for Efficient All-Polymer Solar Cells: A New Strategy of Polymerizing Small Molecule Acceptor

Ultrafast Channel II process induced by a 3-D texture with enhanced acceptor order ranges for high-performance non-fullerene polymer solar cells

Nonconjugated Terpolymer Acceptors with Two Different Fused-Ring Electron-Deficient Building Blocks for Efficient All-Polymer Solar Cells

2D/1a Strategy to Regulate Film Morphology for Efficient and Stable Nonfullerene Organic Solar Cells