Abstract:As part of the ATLAS Phase-I Upgrade, the global Feature EXtractor (gFEX) is one of several hardware modules designed to help maintain the ATLAS Level-1 trigger acceptance rate with the increasing Large Hadron Collider (LHC) luminosity and the increasing Pile-Up conditions. The gFEX is used to identify patterns of energy associated with the hadronic decays of high momentum Higgs, W & Z bosons, top quarks, and exotic particles in real time at the 40 MHz LHC bunch crossing rate. The board is required to receive coarse-granularity (Delta eta x Delta phi) = 0.2 x 0.2 gTower) information from the entire ATLAS calorimeters on 276 optical fibers. A prototype v1 with one Xilinx ZYNQ FPGA, and one Vertex-7 FPGA for technology validation has been designed and tested in 2015. With the lessons learned from the prototype v1, a prototype v2 with three Vertex UltraScale FPGAs and one ZYNQ FPGA has been implemented to verify full functionalities of gFEX in 2016. Based on the prototype v2 design, a prototype v3, the final gFEX prototype, is implemented, which is an ATCA module consisting of three Vertex UltraScale+ FPGAs, one ZYNQ UltraScale+ SoC, and 35 MiniPODs. This board receives up to 300 fiber optical links from calorimeters and transmits trigger data on 96 links to the to the ATLAS Level-1 Topological trigger (L1Topo [1]) at the speed up to 12.8 Gb/s. There are also 24 electrical links on board for communication between two FPGAs with the speed up to 25.6 Gb/s. The performance of three prototype boards have been tested and evaluated. For the prototype v3 board, the high-speed optical links are stable at 12.8 Gb/s with Bit Error Ratio (BER) < 1 x 10(-15). The low-latency parallel GPIO (General Purpose I/O) buses between FPGAs are stable at 1.12 Gb/s. The peripheral components of ZYNQ UltraScale+ SoC, such as 16 GB DDR4 DIMM, UART, SPI flashes, and Ethernet, have also been verified. The test results of the prototype v3 board validate the gFEX technologies, architecture and full functionalities. Now the final production board is being produced.

Development of FEB Configuration Test Board for ATLAS NSW Upgrade.

Development of FEB Test Platform for ATLAS New Small Wheel Upgrade

The Development of the Front-End Boards for the Small-Strip Thin Gap Chambers Detector System of the ATLAS Muon New Small Wheel Upgrade

A Scanning Test System of P/sfeb Based on FPGA XADC for the ATLAS Phase-I Stgc Upgrade

Scanning Test System Prototype of p/sFEB for the ATLAS Phase-I sTGC Trigger Upgrade

Performance of Pad Front-End Board for Small-Strip Thin Gap Chamber with Cosmic Ray Muons

Automatic Test System for Pfeb and Sfeb Mass Production

The Study of Strip Readout Prototype for Atlas Phase-I Muon Trigger Upgrade

A Trigger Inspection Platform for sTGC Detector Front-End Electronic Boards

The Development of the Global Feature Extractor for the LHC Run-3 Upgrade of the L1 Calorimeter Trigger System

Development and data path integration test of the global Feature EXtractor for the ATLAS Level-1 calorimeter trigger system Phase-I upgrade

Felix: A Pcie Based High-Throughput Approach for Interfacing Front-End and Trigger Electronics in the Atlas Upgrade Framework

Development of Telescope Readout System Based on FELIX for Testbeam Experiments

The Implementation of Global Feature EXtractor (gfex) - the ATLAS Calorimeter Level 1 Trigger System for LHC Run-3 Upgrade

The Prototype Design of Gfex — a Component of the L1calo Trigger for the ATLAS Phase-I Upgrade

Note: Development Of Stgc Strip Front-End Readout Prototype For Atlas New Small Wheel Upgrade

High Speed Ethernet Application for the Trigger Electronics of the New Small Wheel

RT2009 Conference Record Template

A Data Acquisition System for HV-CMOS Sensor Research and Development in the Upgrade of ATLAS Experiment.

A Front-End Electronics Prototype Based on Gigabit Ethernet for the ATLAS Small-Strip Thin Gap Chamber

A prototype optical link board with redundancy design for the ATLAS liquid argon calorimeter Phase-2 upgrade