Graphene Enhanced Silicon/carbon Composite As Anode for High Performance Lithium-Ion Batteries

Xiaohui Li,Mengqiang Wu,Tingting Feng,Ziqiang Xu,Jingang Qin,Cheng Chen,Chengyang Tu,Dongxia Wang

DOI: https://doi.org/10.1039/c7ra09818a

IF: 4.036

2017-01-01

RSC Advances

Abstract:Silicon-based anode materials for lithium ion batteries (LIBs) have become a hot research topic due to their remarkably high theoretical capacity (4200 mA h g−1).

What problem does this paper attempt to address?

Firmly Bonded Graphene–silicon Nanocomposites As High-Performance Anode Materials for Lithium-Ion Batteries

Yifan Chen,Ning Du,Hui Zhang,Deren Yang

DOI: https://doi.org/10.1039/c5ra05869d

IF: 4.036

2015-01-01

RSC Advances

Abstract:We demonstrate the synthesis of the firmly bonded reduced graphene oxide (RGO)@Si nanocomposites via the magnesiothermic reduction for high performance LIBs anode materials.
A Graphene-Wrapped Silver–porous Silicon Composite with Enhanced Electrochemical Performance for Lithium-Ion Batteries

Fei-Hu Du,Kai-Xue Wang,Wei Fu,Peng-Fei Gao,Jing-Feng Wang,Jun Yang,Jie-Sheng Chen

DOI: https://doi.org/10.1039/c3ta13092d

IF: 11.9

2013-01-01

Journal of Materials Chemistry A

Abstract:A graphene-wrapped silver-porous silicon composite has been prepared and used as the anode material in lithium-ion batteries (LIBs). Porous silicon (pSi) prepared through a magnesiothermic reduction of mesoporous silica MCM-41 was surface-modified by Ag nanoparticles formed via the thermal decomposition of AgNO3 and then graphene nanosheets (GNS) generated through the thermal reduction of graphene oxide. The obtained Ag-pSi/GNS composite exhibits a distinctly high reversible specific capacity, long cycling performance and super rate capability. An initial capacity as high as 3531 mA h g(-1) is delivered at 0.1 A g(-1), whereas at a current density of 32 A g(-1), a specific capacity of 1241 mA h g(-1), more than three times higher than the theoretical capacity of the graphite anode, is still retained for 50 cycles. The superior electrochemical performance demonstrates that this Ag-pSi/GNS composite is a promising electrode material for high-performance LIBs.
Effect of Graphene on the Performance of Silicon–Carbon Composite Anode Materials for Lithium-Ion Batteries

Chengyuan Ni,Chengdong Xia,X. Lei,Wei Xu,Wenping Liu,Zhiqiang Shan,Zhendong Tao,Haiqing Qin

DOI: https://doi.org/10.3390/ma17030754

IF: 3.4

2024-02-01

Materials

Abstract:(Si/graphite)@C and (Si/graphite/graphene)@C were synthesized by coating asphalt-cracked carbon on the surface of a Si-based precursor by spray drying, followed by heat treatment at 1000 °C under vacuum for 2h. The impact of graphene on the performance of silicon–carbon composite-based anode materials for lithium-ion batteries (LIBs) was investigated. Transmission electron microscopy (TEM) and selected area electron diffraction (SAED) images of (Si/graphite/graphene)@C showed that the nano-Si and graphene particles were dispersed on the surface of graphite, and thermogravimetric analysis (TGA) curves indicated that the content of silicon in the (Si/graphite/graphene)@C was 18.91%. More bituminous cracking carbon formed on the surface of the (Si/graphite/graphene)@C due to the large specific surface area of graphene. (Si/Graphite/Graphene)@C delivered first discharge and charge capacities of 860.4 and 782.1 mAh/g, respectively, initial coulombic efficiency (ICE) of 90.9%, and capacity retention of 74.5% after 200 cycles. The addition of graphene effectively improved the cycling performance of the Si-based anode materials, which can be attributed to the reduction of electrochemical polarization due to the good structural stability and high conductivity of graphene.

Chemistry,Engineering,Medicine,Materials Science
Graphene supported double-layer carbon encapsulated silicon for high-performance lithium-ion battery anode materials

Yanhong Lu,Zhantong Ye,Yating Zhao,Qing Li,Meiyu He,Congcong Bai,Xiaotong Wang,Yalu Han,Xingchen Wan,Suling Zhang,Yanfeng Ma,Yongsheng Chen

DOI: https://doi.org/10.1016/j.carbon.2022.10.010

IF: 10.9

2023-01-05

Carbon

Abstract:Carbon coating has been an effective procedure to tackle the severe structural degradation and poor conductivity during cycling of silicon-based anodes in lithium-ion batteries (LIBs). However, the traditional coated carbon usually is tight and thus limit the fast-charging rate and high specific capacity. Herein, through in-situ formation of metal-organic frameworks on the surface, silicon particles were firstly coated by an inside carbon layer. Followed by a solvothermal reaction with the mixture of sucrose and graphene oxide, the second carbon layer outside the silicon particles was deposited, and simultaneously a highly conductive graphene network was formed. After a high temperature pyrolysis process, a graphene matrix supported silicon material with inward multi-channel carbon and outward tight activated carbon was prepared. This unique core/double-layer carbon structure, combined with the highly conductive graphene frameworks, render the material to demonstrate excellent electrochemical performance as anode materials for LIBs in terms of both lithium storage capacity and cycling stability. Thus, the electrode materials deliver a high specific capacity of 1528.1 mA h g−1 at the current density of 0.1 A g−1 and rate capacity retention of 45.5% at 1 A g−1 to 0.1 A g−1. Simultaneously, a highly stable reversible capacity of 1182 mAh g−1 with 89.5% retention over 240 cycles at a current density of 0.2 A g−1 and 484 mAh g−1 with 76.8% retention after 450 cycles at 1.0 A g−1 were obtained. This work can offer an alternative approach for high-energy and low-cost silicon-based anodes for LIBs.

materials science, multidisciplinary,chemistry, physical
Facile preparation of micron-sized silicon-graphite‐carbon composite as anode material for high-performance lithium-ion batteries

Fangfang Zhao,Min Zhao,Yanru Dong,Lei Ma,Yu Zhang,Sulin Niu,Liangming Wei

DOI: https://doi.org/10.1016/j.powtec.2022.117455

IF: 5.64

2022-04-01

Powder Technology

Abstract:Silicon/carbon (Si/C) composites have become the mainstream anodes for silicon-based lithium-ion batteries (LIBs) with outstanding stability and high capacity, in which carbon can significantly stabilize the silicon anodes. Currently, most Si/C composites use nano‑silicon as raw materials, which suffer from low energy density, high price and preparation complexity. Here, we have developed a silicon-graphite‑carbon ternary composite (Si-G-C-15) with cheap micron-sized silicon as raw materials. It was prepared by ball-milling of micron silicon and graphite and subsequent carbonization of PAN, followed by NaOH selective etching. Electrochemical test results demonstrate that Si-G-C-15 can possess a reversible capacity of 965 mAh/g at 200 mA/g, with a capacity retention of 71.34% and 786 mAh/g at a high current density of 1 A/g after 100 cycles. Notably, this facile preparation process of silicon anodes with high rates and good capacity stability highlights the potential practical application.

engineering, chemical
Hierarchical Graphene-Scaffolded Silicon/Graphite Composites as High Performance Anodes for Lithium-Ion Batteries.

Shanshan Zhu,Jianbin Zhou,Yong Guan,Wenlong Cai,Yingyue Zhao,Yuanchao Zhu,Linqin Zhu,Yongchun Zhu,Yitai Qian

DOI: https://doi.org/10.1002/smll.201802457

IF: 13.3

2018-01-01

Small

Abstract:To better couple with commercial cathodes, such as LiCoO2 and LiFePO4, graphite-based composites containing a small proportion of silicon are recognized as promising anodes for practical application in lithium-ion batteries (LIBs). However, the prepared Si/C composite still suffers from either rapid capacity fading or the high cost up to now. Here, the facile preparation of hierarchical graphene-scaffolded silicon/graphite composite is reported. In this designed 3D structure, Si nanoparticles are homogeneously dispersed on commercial graphites and then uniformly encapsulated in the hierarchical graphene scaffold. This hierarchical structure is also well characterized by the synchrotron X-ray computed nanotomography technique. When evaluated as anodes for LIBs, the hierarchical composite, with the Si weight ratio of 5 wt%, exhibits a reversible capacity of 559 mA h g(-1) at 75 mA g(-1), suggesting an unprecedented utilization of Si up to 95%. Even at 372 mA g(-1), the composite can still maintain a high capacity retention of 90% after 100 cycles. Coupled with the LiFePO4 cathode, the full cell shows the high capacity of 114 mA h g(-1) at 170 mA g(-1). The excellent Li-storage properties can be ascribed to the unique designed hierarchical structure.
High Rate Capability and Long Cycling Life of Graphene-Coated Silicon Composite Anodes for Lithium Ion Batteries

Jingang Qin,Mengqiang Wu,Tingting Feng,Cheng Chen,Chengyang Tu,Xiaohui Li,Chen Duan,Dawei Xia,Dongxia Wang

DOI: https://doi.org/10.1016/j.electacta.2017.10.022

IF: 6.6

2017-01-01

Electrochimica Acta

Abstract:With a theoretical specific capacity much higher than that of traditional graphite, silicon (Si) has been considered as a promising anode material for next-generation lithium ion batteries (LIBs). Unfortunately, its practical application has been severely limited by the drawback of drastic volume expansion. In this report, we demonstrate a facile way to prepare binder-free, conductive agent-free silicon/reduced graphene oxide composite (Si/rGO) anode on nickel foam via one-step hydrothermal method followed by a post-annealing process, which delivers extraordinary cyclability and rate performance. The reversible specific capacity of the composite anode retained over 1500mAh/g at 2A/g after 2500 cycles and over 600mAh/g at 4A/g after 2500 cycles. Especially at a reasonable high current density of 16A/g, the Si/rGO anode still displayed a specific capacity of 500mAh/g.
Graphene Caging Silicon Particles for High-Performance Lithium-Ion Batteries.

Ping Nie,Zaiyuan Le,Gen Chen,Dan Liu,Xiaoyan Liu,Hao Bin Wu,Pengcheng Xu,Xinru Li,Fang Liu,Limin Chang,Xiaogang Zhang,Yunfeng Lu

DOI: https://doi.org/10.1002/smll.201800635

IF: 13.3

2018-01-01

Small

Abstract:Silicon holds great promise as an anode material for lithium-ion batteries with higher energy density; its implication, however, is limited by rapid capacity fading. A catalytic growth of graphene cages on composite particles of magnesium oxide and silicon, which are made by magnesiothermic reduction reaction of silica particles, is reported herein. Catalyzed by the magnesium oxide, graphene cages can be conformally grown onto the composite particles, leading to the formation of hollow graphene-encapsulated Si particles. Such materials exhibit excellent lithium storage properties in terms of high specific capacity, remarkable rate capability (890 mAh g(-1) at 5 A g(-1)), and good cycling retention over 200 cycles with consistently high coulombic efficiency at a current density of 1 A g(-1). A full battery test using LiCoO2 as the cathode demonstrates a high energy density of 329 Wh kg(-1).
Porous Silicon–graphene–carbon Composite As High Performance Anode Material for Lithium Ion Batteries

Yuehua Huang,Jing Luo,Jiao Peng,Minhao Shi,Xingxing Li,Xianyou Wang,Baobao Chang

DOI: https://doi.org/10.1016/j.est.2019.101075

IF: 9.4

2019-01-01

Journal of Energy Storage

Abstract:The porous silicon-graphene-carbon (SGC) composite is prepared by freeze-drying and chemical vapor deposition (CVD) process with commercially available nano-silicon, phenolic resin and graphene oxide as raw materials. The self-assembly process makes the nano-silicon into a porous structure and uniform recombination with the graphene oxide, and finally a nano-carbon layer is coated on the surface of the SGC composite by a CVD process. The composition, morphology and pore properties of SGC composite are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and pore size analysis. The nano-carbon layer on the surface of the SGC is examined by transmission electron microscopy (TEM) and Raman spectrometer. The contents of C, Si and O in precursor and SGC are analyzed by X-Ray Fluorescence (XRF), and the electrochemical performances of composite material are analyzed by half-cell and full-cell experiments. The results show that the SGC composite is porous structure with the average pore size of 20-30 nm, and the surface of the porous silicon-graphene is coated by a thickness of 5 nm carbon layers. The reversible capacity and initial coulombic efficiency (ICE) of the SGC are 2180 mAh g(-1) and 79.3%. The capacity retention is higher than 70.1% after 100 charge/discharge cycles by the half-cell experiment; and the capacity of the composite anode is still as high as 550 m Ah g(-1) after 820 charge/discharge cycles by full-cell experiment. Therefore, the structure design strategy of the composite is beneficial to buffer the volume effect of nano-silicon, prevent iterative growth of the SEI film and boost the electrochemical performances.
Homogeneously Dispersed Silicon/Graphite Composite Toward Enhanced Lithium-Ion Batteries

Zhaojin Li,Conghao Shi,Pengfei Liu,Yunbo Di,Di Zhang,Qiujun Wang,Huilan Sun,Qujiang Sun,Bo Wang

DOI: https://doi.org/10.1016/j.est.2024.111673

IF: 9.4

2024-01-01

Journal of Energy Storage

Abstract:At present, silicon/graphite composite is the most promising anode material for high energy density lithium-ion batteries. However, during the preparation, nanoscale silicon will inevitably undergo agglomeration, which will cause serious volume changes and breakage during the charging/discharging process. How to achieve uniform dispersion of nanoscale silicon on the surface of graphite becomes a great challenge. Here, by grafting functional groups on the surface of silicon, both the repulsive force between silicon particles and the binding force between silicon/graphite have been improved, thereby highly uniform dispersed silicon is achieved. After being coated with asphalt and etching off the functional groups, the conductivity and ion migration ability of the composite are further improved. Resultantly, the modified composite provides a high discharging capacity of 598.4 mAh·g−1 at 0.2 C and can still maintain a high-capacity retention of 90.7 % and a small volume expansion rate of 30.8 % after 500 cycles.
Carbon-coated silicon/graphite oxide composites as anode for highly stable lithium-ion batteries

Lujie Niu,Rui Zhang,Qiang Zhang,Dong Wang,Yanlei Bi,Guangwu Wen,Lu-Chang Qin

DOI: https://doi.org/10.1039/d4cp01424c

IF: 3.3

2024-05-31

Physical Chemistry Chemical Physics

Abstract:Silicon (Si) has been widely investigated as anodes of lithium-ion batteries (LIBs) due to its high theoretical capacity. However, the huge volume expansion and low electrical conductivity limit its practical application to some extent. Here, we prepared a composite structure in which the ammonia-modified Si NPs well encapsulated in graphene oxide (GO) through electrostatic attraction are further wrapped by amorphous carbon. The GO with good flexibility can well buffer the volume expansion of Si NPs, while the amorphous carbon in the outer layer is synergistically constructed with GO as a second protective layer for Si NPs. The ternary composite (Si/G/C) approach greatly ensures the structural integrity of the composites and have excellent cycling as well as rate performance compared to Si/reduced graphene oxide and Si/carbon composites. For the Si/G/C, at a current density of 1 A/g, it can be stably cycled over 267 times with 70% capacity maintained (only 0.0711% capacity reduction per cycle).

chemistry, physical,physics, atomic, molecular & chemical
Carbon-coated Silicon/graphite Oxide Composites As Anode Materials for Highly Stable Lithium-Ion Batteries

Lujie Niu,Rui Zhang,Qiang Zhang,Dong Wang,Yanlei Bi,Guangwu Wen,Lu-Chang Qin

DOI: https://doi.org/10.1039/d4cp01424c

IF: 3.3

2024-01-01

Physical Chemistry Chemical Physics

Abstract:Silicon (Si) has been widely investigated as an anode material for lithium-ion batteries (LIBs) due to its high theoretical capacity. However, the huge volume expansion and low electrical conductivity limit its practical application to some extent. Here, we prepared silicon/reduced graphene oxide/amorphous carbon (Si/G/C) anode materials for lithium-ion batteries using a facile synergistic cladding layer. The protective effect of different carbon layers was explored and it was found that ternary composites have excellent electrochemical properties. In this work, the surface of Si was first modified using ammonia, and the positively charged Si was tightly anchored to the graphene sheet layer. In contrast, amorphous carbon was used as a reinforcing coating for further coating to synergistically build up the cladding layer of Si NPs with graphene oxide. The ternary composite (Si/G/C) material greatly ensures the structural integrity of the composites and shows excellent cycling as well as rate performance compared to Si/reduced graphene oxide and Si/carbon composites. For the Si/G/C composite, at a current density of 1 A g-1, it can be stably cycled over 267 times with 70% capacity retention (only 0.0711% capacity reduction per cycle). The cycling stability of Si materials is greatly enhanced by the introduction of two carbon sources.
Fabrication of honeycomb-like amorphous carbon-encapsulated Si nanoparticles/graphene composite for superior lithium storage

Jiafeng Gao,Yu Liu,Jianqiang Chen,He Liu,Xiaoling Li,Ziqi Wang,Zui Chen,Yutong Xu,Jie Wang

DOI: https://doi.org/10.1016/j.est.2023.109351

IF: 9.4

2023-11-02

Journal of Energy Storage

Abstract:Silicon (Si) anodes have great potential for high-energy lithium-ion batteries (LIBs). However, poor electrical conductivity, high cost and huge volume change during the (de)lithiation processes of silicon anodes hinder the practical application. Herein, we demonstrate a facile and scalable approach to fabricate a porous honeycomb-like amorphous carbon-encapsulated Si nanoparticles/graphene composite via a sol-gel & CO 2 -introduced magnesiothermic reduction method. The greenhouse gas CO 2 is efficiently transformed into carbon layers. Interconnected carbon network consisting of graphene sheets and amorphous carbon layers not only significantly improves the electrical conductivity and mechanical properties of the Si-based composites, but also provides the strong interaction between Si and carbon materials. Besides, both unique honeycomb-like porous structure and interconnected carbon network can butter large volume effects of Si nanoparticles. The as-prepared amorphous carbon-encapsulated Si/graphene anode with the carbon content of 8 wt% has excellent rate performance and outstanding cycling stability, delivering a high discharge capacity of 908 mAh g −1 with 65.9 % of capacity retention at 0.5 A g −1 after 200 cycles. Thus, such honeycomb-like amorphous carbon-encapsulated Si nanoparticles/graphene composite anode is highly promising for practical next-generation LIBs.

energy & fuels
Silicon Nanoparticles Embedded in Chemical-Expanded Graphite through Electrostatic Attraction for High-Performance Lithium-Ion Batteries

Xu Liu,Huitian Liu,Yuhao Cao,Xiaochen Wu,Zhongqiang Shan

DOI: https://doi.org/10.1021/acsami.2c21866

2023-02-09

Abstract:Silicon (Si) is a promising next-generation anode for high-energy-density lithium-ion batteries. The application of silicon/carbon (Si/C) composites with high Si content is hindered by the huge volume change and insecure electrochemical interface of the Si anode. Herein, chemical-expanded graphite (CEG) is used as a carbon matrix to form Si@CEG/C composites with an embedded structure. CEG with an abundant pore structure and electropositivity can well disperse and accommodate a mass of Si nanoparticles (Si NPs). With the flexibility and porosity of CEG, the embedded structure of Si NPs fixed in an expanded graphite layer can adopt the volume change of Si NPs and offer the abundant path of diffusion of lithium-ion, which leads to a moderate cycle and rate performance. Si@CEG/C exhibits a high reversible capacity of 1232.4 mA h g-1 at a current density of 0.5 A g-1 and with a capacity retention rate of 87% after 200 cycles. This embedded structure of Si/C composites built by CEG is meaningful for the structure design of the Si-based anode with higher specific capacity, active material utilization, and satisfactory cycle stability.
Nano-porous Si/C Composites for Anode Material of Lithium-Ion Batteries

Ying Zheng,Jun Yang,Jiulin Wang,Yanna NuLi

DOI: https://doi.org/10.1016/j.electacta.2007.03.013

IF: 6.6

2007-01-01

Electrochimica Acta

Abstract:Nano-porous silicon composite incorporated with graphite and pyrolyzed carbon was synthesized and investigated as a promising anode material for lithium-ion batteries. The nano-porous Si/graphite composite was prepared via two-step ball-milling followed by etching process. Then carbon was incorporated by using different approaches. The nano-porous Si/graphite/C composite exhibits a reversible capacity of about 700mAh/g with no capacity loss up to the 120th cycle at a constant current density of 0.2mA/cm2. The superior electrochemical characteristics are attributed to the nanosized pores in Si particles, which suppress the volume effect, and buffering action as well as excellent electronic and ionic conductivity of carbon materials.
High-Performance Silicon Battery Anodes Enabled by Engineering Graphene Assemblies

Min Zhou,Xianglong Li,Bin Wang,Yunbo Zhang,Jing Ning,Zhichang Xiao,Xinghao Zhang,Yanhong Chang,Linjie Zhi

DOI: https://doi.org/10.1021/acs.nanolett.5b02697

IF: 10.8

2015-01-01

Nano Letters

Abstract:We propose a novel material/electrode design formula and develop an engineered self-supporting electrode configuration, namely, silicon nanoparticle impregnated assemblies of templated carbon-bridged oriented graphene. We have demonstrated their use as binder-free lithium-ion battery anodes with exceptional lithium storage performances, simultaneously attaining high gravimetric capacity (1390 mAh g(-1) at 2 A g(-1) with respect to the total electrode weight), high volumetric capacity (1807 mAh cm(-3) that is more than three times that of graphite anodes), remarkable rate capability (900 mAh g(-1) at 8 A g(-1)), excellent cyclic stability (0.025% decay per cycle over 200 cycles), and competing areal capacity (as high as 4 and 6 mAh cm(-2) at 15 and 3 mA cm(-2), respectively). Such combined level of performance is attributed to the templated carbon bridged oriented graphene assemblies involved. This engineered graphene bulk assemblies not only create a robust bicontinuous network for rapid transport of both electrons and lithium ions throughout the electrode even at high material mass loading but also allow achieving a substantially high material tap density (1.3 g cm(-3)). Coupled with a simple and flexible fabrication protocol as well as practically scalable raw materials (e.g., silicon nanoparticles and graphene oxide), the material/electrode design developed would propagate new and viable battery material/electrode design principles and opportunities for energy storage systems with high-energy and high-power characteristics.
Graphene-doped silicon-carbon materials with multi-interface structures for lithium-ion battery anodes

Xin Li,Kun Li,Man Yuan,Jiapeng Zhang,Haiyan Liu,Ang Li,Xiaohong Chen,Huaihe Song

DOI: https://doi.org/10.1016/j.jcis.2024.04.113

Abstract:The carbon nanomaterials are usually used to improve the electrical conductivity and stability of silicon (Si) anodes for lithium-ion batteries. However, the Si-based composites containing carbon nanomaterials generally show large specific surface area, leading to severe side reactions that generate large amounts of solid electrolyte interphase films. Herein, we embedded graphene oxide (GO) and silicon nanoparticles (Si NPs) uniformly in pitch matrix by solvent dispersion. The internally doped GO reduces the exposed surface and improves the electrical conductivity of the composite. Meanwhile, the multi-interface structures are constructed inside to limit the domains of Si NPs and improve the structural stability of the material. When evaluated as anodes, the Si/graphene/pitch-based carbon composite anode exhibits the outstanding electrochemical properties, delivering a reversible capacity of 820.8 mAh/g at 50 mA g-1, as well as a capacity retention of 93.6 % after 1000 cycles at 2 A/g. In addition, when assembled with the LiFePO4 cathode, the full cell exhibits an impressive capacity retention of 95 % after 100 cycles at 85 mA g-1. This work provides a valuable design concept for the development of Si/carbon anodes.
Sub-nanometer structured silicon-carbon composite nanolayers armoring on graphite for fast-charging and high-energy-density lithium-ion batteries

Zhen-Wei Li,Mei-Sheng Han,Jie Yu

DOI: https://doi.org/10.1007/s12598-023-02395-w

IF: 6.318

2023-09-20

Rare Metals

Abstract:Silicon/carbon composites are promising alternatives to current graphite anodes in commercial lithium-ion batteries (LIBs) because of their high capacity and excellent safety. Nevertheless, the unsatisfactory fast-charging capability and cycle stability of Si/C composites caused by slow charge transport capability and huge volume change under industrial electrode conditions severely hamper their development. Here, a novel Si/C anode was fabricated by homogeneously depositing amorphous C-Si nanolayers on graphite (C-Si@graphite). C-Si nanolayers with uniformly dispersed sub-nanometer Si particles in 3D carbon skeleton significantly boost electron and Li-ion transport and efficiently relieve Si's agglomeration and volume change. As a result, the tailored C-Si@graphite electrodes show an excellent rate capacity (760.3 mAh·g−1 at 5.0C) and long cycle life of over 1000 cycles at 1.0C and 800 cycles at 2.0C under industrial electrode conditions. In addition, the assembled full cells (C-Si@graphite, anode; Li[Ni0.8Co0.1Mn0.1]O2, cathode) present superior fast-charging capability (240.4 Wh·kg−1, charging for 16.2 min, 3.0C) and long cycle life (80.7% capacity retention after 500 cycles at 1.0C), demonstrating the massive potential of C-Si@graphite for practical application.Graphical abstract

materials science, multidisciplinary,metallurgy & metallurgical engineering
Silicon is Embedded in Graphene Layers Through High-Energy Ball Milling as the Anode Material for Lithium-Ion Batteries

WenHao Li,Shaopeng Wu,Xusheng Liu,Yuanchao Cheng,Xiaolan Cai,Lei Zhou,YanKun Wang,QingLan Huang

DOI: https://doi.org/10.1080/10584587.2023.2191505

2023-05-12

Integrated Ferroelectrics

Abstract:Using micron silicon as raw material and multi-layer graphene as carbon source, a sandwich-type silicon-carbon composite material is prepared by high-energy ball milling, in which micro-silicon particles are uniformly embedded between the layers of multi-layer graphene. In the process of lithium deintercalation, the graphene sheet can effectively suppress the volume expansion of silicon, thereby improving the high cycle performance and electronic conductivity of the negative electrode of lithium ion batteries. The results show that the average discharge specific capacities are 3094.8, 2406.1, 1845.2, 1210.1, 657.3mAh/g at current densities of 200, 400, 800, 2000, and 4000mAh/g. Each current density is cycled for 5 cycles. When returning from high current to low current, the capacity can still remain at 1729.4 mAh/g, which is greatly improved compared to 671.4 mAh/g of pure silicon. important meaning. It is of great significance for the application of high-capacity silicon carbon anodes.

engineering, electrical & electronic,physics, condensed matter, applied
An interconnected and scalable hollow Si-C nanospheres/graphite composite for high-performance lithium-ion batteries

Jiafeng Gao,Songlin Zuo,He Liu,Qiwen Jiang,Chenhao Wang,Huanhuan Yin,Ziqi Wang,Jie Wang

DOI: https://doi.org/10.1016/j.jcis.2022.05.135

IF: 9.9

2022-10-15

Journal of Colloid and Interface Science

Abstract:Silicon (Si) anode is the most promising alternative for next generation lithium-ion batteries (LIBs) owing to large theoretical capacity, low working voltage and abundant natural resources. However, tremendous volume change of Si during the (de)lithiation processes causes repetitive formation of solid electrolyte interphase (SEI) layers, loss of electrical contact and electrodes pulverization, limiting its commercial application. Herein, we fabricate an interconnected hollow Si-C nanospheres/graphite composite via a facile and scalable approach. Notably, hollow Si-C nanospheres and graphite are homogeneously combined by using the surfactants as surface modifiers of graphite and introducing carbon dioxide (CO2) into magnesiothermic reduction reaction, resulting in the enhanced compatibility between hollow Si-C nanospheres and graphite, and the well-established electrical conductive network. The resultant Si-C nanospheres/graphite composite anode with carbon content of 59 wt% delivers a large reversible specific capacity of 662 mAh g−1 and a high capacity retention of 65.7% at 0.5 A g−1 after 200 cycles. Such excellent rate performance and superior cycling performance are attributed to high electrical conductivity and buffering effect of graphite, superior compatibility between hollow Si-C spheres and graphite, uniform distribution of both Si-C nanospheres with a unique hollow architecture and graphite flakes inside the composites and well-established interconnected electrical conductive carbon networks, which can effectively alleviate Si volume expansion and maintain good electrical contact during cycling. This strategy provides insights into designing Si-based anodes for practical LIBs.

chemistry, physical

Graphene Enhanced Silicon/carbon Composite As Anode for High Performance Lithium-Ion Batteries

Firmly Bonded Graphene–silicon Nanocomposites As High-Performance Anode Materials for Lithium-Ion Batteries

A Graphene-Wrapped Silver–porous Silicon Composite with Enhanced Electrochemical Performance for Lithium-Ion Batteries

Effect of Graphene on the Performance of Silicon–Carbon Composite Anode Materials for Lithium-Ion Batteries

Graphene supported double-layer carbon encapsulated silicon for high-performance lithium-ion battery anode materials

Facile preparation of micron-sized silicon-graphite‐carbon composite as anode material for high-performance lithium-ion batteries

Hierarchical Graphene-Scaffolded Silicon/Graphite Composites as High Performance Anodes for Lithium-Ion Batteries.

High Rate Capability and Long Cycling Life of Graphene-Coated Silicon Composite Anodes for Lithium Ion Batteries

Graphene Caging Silicon Particles for High-Performance Lithium-Ion Batteries.

Porous Silicon–graphene–carbon Composite As High Performance Anode Material for Lithium Ion Batteries

Homogeneously Dispersed Silicon/Graphite Composite Toward Enhanced Lithium-Ion Batteries

Carbon-coated silicon/graphite oxide composites as anode for highly stable lithium-ion batteries

Carbon-coated Silicon/graphite Oxide Composites As Anode Materials for Highly Stable Lithium-Ion Batteries

Fabrication of honeycomb-like amorphous carbon-encapsulated Si nanoparticles/graphene composite for superior lithium storage

Silicon Nanoparticles Embedded in Chemical-Expanded Graphite through Electrostatic Attraction for High-Performance Lithium-Ion Batteries

Nano-porous Si/C Composites for Anode Material of Lithium-Ion Batteries

High-Performance Silicon Battery Anodes Enabled by Engineering Graphene Assemblies

Graphene-doped silicon-carbon materials with multi-interface structures for lithium-ion battery anodes

Sub-nanometer structured silicon-carbon composite nanolayers armoring on graphite for fast-charging and high-energy-density lithium-ion batteries

Silicon is Embedded in Graphene Layers Through High-Energy Ball Milling as the Anode Material for Lithium-Ion Batteries

An interconnected and scalable hollow Si-C nanospheres/graphite composite for high-performance lithium-ion batteries