Abstract:The so-called bimodal microstructure of Ti-6Al-4V alloy, composed of primary α grains (αp) and transformed β areas (βtrans), can be regarded as a “dual-phase” structure to some extent, the mechanical properties of which are closely related to the sizes, volume fractions, distributions as well as nano-hardness of the two constituents. In this study, the volume fractions of primary α grains (vol.%(αp)) were systematically modified in three series of bimodal microstructures with fixed primary α grain sizes (0.8 μm, 2.4 μm and 5.0 μm), by changing the intercritical annealing temperature (Tint). By evaluating the tensile properties at room temperature, it was found that with increasing Tint (decreasing vol.%(αp)), the yield strength of bimodal microstructures monotonically increased, while the uniform elongation firstly increased with Tint until 910 °C and then drastically decreased afterwards, thereby dividing the Tint into two regions, namely region I (830−910 °C) and region II (910−970 °C). The detailed deformation behaviors within the two regions were studied and compared, from the perspectives of strain distribution analysis, slip system analysis as well as dislocation analysis. For bimodal microstructures in region I, due to the much lower nano-hardness of βtrans than αp, there was a clear strain partitioning between the two constituents as well as a strain gradient from the αp/βtrans interface to the grain interior of αp. This activated a large number of geometrically necessary dislocations (GNDs) near the interface, mostly with components, which contributed greatly to the extraordinary work-hardening abilities of bimodal microstructures in region I. With increasing Tint, the αp/βtrans interface length density gradually increased and so was the density of GNDs with components, which explained the continuous increase of uniform elongation with Tint in this region. For bimodal microstructures in region II, where the nano-hardness of βtrans and αp were comparable, neither a clear strain-partitioning tendency nor a strain gradient across the αp/βtrans interface was observed. Consequently, only statistically stored dislocations (SSDs) with component were activated inside αp. The absence of dislocations together with a decreased volume fraction of αp resulted into a dramatic loss of uniform elongation for bimodal microstructures in region II.

Bimodal Eutectic Titanium Alloys: Microstructure Evolution, Mechanical Behavior and Strengthening Mechanism

Bimodal Titanium Alloys with Ultrafine Lamellar Eutectic Structure Fabricated by Semi-Solid Sintering

Designing Ultrafine Lamellar Eutectic Structure in Bimodal Titanium Alloys by Semi-Solid Sintering

Fabrication of Novel Bimodal Titanium Alloy with High-Strength and Large-Ductility by Semi-Solid Sintering

A new insight into high-strength Ti 62 Nb 12.2 Fe 13.6 Co 6.4 Al 5.8 alloys with bimodal microstructure fabricated by semi-solid sintering

Bi-modally grained Ti-based alloys fabricated by semi-solid sintering based on the hypoeutectic transformation

A bimodal microstructure to improve the strength-ductility properties of Ti-Cu alloys by using eutectoid reactive laser depositing

Design of Bimorphic-Bimodal Microstructure in Titanium Alloys by Semi-Solid Sintering

Processing, Multiscale Microstructure Refinement and Mechanical Property Enhancement of Hypoeutectic Al–Si Alloys Via in Situ Bimodal-Sized TiB2 Particles

Eutectic Microstructure Evolution of Directionally Solidified Nb-Ti-Si Base Ultrahigh Temperature Alloy

Deformation Mechanism of Bimodal Microstructure in Ti-6Al-4V Alloy: the Effects of Intercritical Annealing Temperature and Constituent Hardness

Microstructure and Mechanical Properties of TiNbFeCoAl Alloys Prepared by Semi-Solid Sintering Assisted by Thermo-Mechanical Field

Synergic strength-ductility enhancement in bimodal titanium alloy via a heterogeneous structure induced by the <c+a> slip

Microstructural Sensitivity and Deformation Micro-Mechanisms of a Bimodal Metastable Β Titanium Ti–7Mo–3Nb–3Cr–3Al Alloy

The Conflicts Between Strength and Ductility of Bimodal Ti-5553 Alloy with Fine Equiaxial Prior Β Grains

Microstructure and Mechanical Properties of Bimodal Ti-Bi Alloys Fabricated by Mechanical Alloying and Spark Plasma Sintering for Biomedical Applications

Bimodal Structured Ti-base Alloy with Large Elasticity and Low Young's Modulus

Enhanced Mechanical Properties of Ti-5Al-5Mo-5V-3Cr-1Zr by Bimodal Lamellar Precipitate Microstructures Via Two-Step Aging

Substructure and Texture Evolution of a Novel Near-Α Titanium Alloy with Bimodal Microstructure During Hot Compression in Α+Β Phase Region

Influence of Microstructure on Tensile Properties and Deformation Mechanism of Ti-5Al-1V-1Sn-1Zr-0.8Mo Alloy: Bimodal Versus Basketweave Structures

Microstructure, Mechanical Properties and Strengthening Mechanism of Tib2 Nanoparticles-Reinforced Cocrfemnni High-Entropy Alloy