Abstract:Proton exchange membrane fuel cells (PEMFCs) should further reduce the platinum consumption to lower their manufacturing costs and life-cycle carbon emissions. However, the performance of the catalyst layers with low-Pt loading needs to be improved. Short-side-chain (SSC) ionomers have been proven to enhance the catalytic activity of conventional catalyst layers. In this work, the SSC ionomer was applied to the electrospun catalyst layer, and achieved a remarkable improvement in the performance. With the use of commercially available catalyst, the membrane electrode assemblies (MEAs) prepared in this work exhibited a low total-Pt-consumption of 0.064 g kW -1 (stoichiometric ratios of 1.5/2.5 for H 2 /air, 80 degrees C, 100 kPa) and achieved the 2025 target proposed by the US Department of Energy. Separating activation, ohmic, and concentration overpotentials, the performance enhancement of the electrospun catalyst layer mainly came from the decrease of ohmic overpotential and concentration overpotential. The electrospun ionomer membrane without catalyst was used as a research model to explore the proton transport properties inside the electrospun catalyst layer. The results showed that in the range of PEMFC operating temperature, the proton conductivity of the electrospun catalyst layer could be higher, but meanwhile the proton-conduction activation energy was also elevated. Compared with the conventional catalyst layer, the electrospun catalyst layer showed obviously better performance before and after accelerated stress test, thus verifying the practicality of the electrospun catalyst layers. This work provided a reference for the development of low platinum and high performance catalyst layers.

A High-Performance PEM Fuel Cell with Ultralow Platinum Electrode Via Electrospinning and Underpotential Deposition

Ultralow Platinum Catalysts for High Performance Fuel Cells: in Situ Encapsulation of Platinum Atoms and CoPt3 in 3D Hollow Nanoshells

Development of Composite Non-Platinum IrFe (1:16)/C Nanoparticle As Novel Anodic Catalyst in PEMFC

Improving the High-Current-Density Performance of PEMFC Through Much Enhanced Utilization of Platinum Electrocatalysts on Carbon

Ultra-low Catalyst Loading Cathode Electrode for Anion-Exchange Membrane Fuel Cells

Highly Active And Durable Carbon Support Pt-Rare Earth Catalyst For Proton Exchange Membrane Fuel Cell

Performance of Proton Exchange Membrane Fuel Cell Electrodes Prepared by Direct Deposition of Ultrathin Platinum on the Membrane Surface

A Study on Novel Pulse Preparation and Electrocatalytic Activities of Pt/C-Nafion Electrodes for Proton Exchange Membrane Fuel Cell

Preparing PEMFC Electrodes by Ultrasonic-Spray Technique

Electrodepositing Pt by Modulated Pulse Current on A Nafion-Bonded Carbon Substrate As an Electrode for Pemfc

Nano-engineering of a 3D-ordered membrane electrode assembly with ultrathin Pt skin on open-walled PdCo nanotube arrays for fuel cells

Electrospun Catalyst Layers Using Short-Side-chain Ionomer for Low Platinum and High Performance PEMFCs

Highly Dispersed Palladium Nanoparticles on Carbon-Decorated Porous Nickel Electrode: an Effective Strategy to Boost Direct Ethanol Fuel Cell Up to 202 Mw Cm–2

Durable hybrid electrocatalysts for proton exchange membrane fuel cells

High Performance PEM Fuel Cell with Low Platinum Loading at the Cathode Using Magnetron Sputter Deposition

One‐Step Fabrication of Ultralow Pt Loading High Efficiency Proton Exchange Membrane for Water Electrolysis by Conventional E‐Beam Metal Deposition

Self‐Standing Nanofiber Electrodes with Pt–Co Derived from Electrospun Zeolitic Imidazolate Framework for High Temperature PEM Fuel Cells

Ultrathin Nanoporous Metal Electrodes Facilitate High Proton Conduction for Low-Pt PEMFCs

Preparation of Oxygen Reduction Catalyst Electrodes by Electrochemical Acidification and Synergistic Electrodeposition

Membrane Electrode Assembly with Ultra Low Platinum Loading for Cathode Electrode of PEM Fuel Cell by Using Sputter Deposition

Bio-inspired Construction of Advanced Fuel Cell Cathode with Pt Anchored in Ordered Hybrid Polymer Matrix