Abstract:Injection of CO2 and water in saline aquifers or oil reservoirs causes changes of pressure, saturation and concentrations that affect the state of stress and promote chemical reactions in the host rock, resulting in porosity and permeability variations. It is therefore a coupled hydro-mechanical and chemical (HMC) problem. Numerical simulation of multiphase and multicomponent flow of CO2, oil and water with mechanical coupling allows realistic modeling of the reservoir and cap rocks. Carbonate reservoirs are geological formations composed mainly of minerals such as calcite and dolomite which can dissolve or precipitate in the medium when injecting a fluid of chemical composition and temperature different from those of the fluids initially contained in the rock. Water-weakening due to matrix acidification of carbonates is a well-known phenomenon that can be modeled by including mineral concentrations as state variables in the stress-strain behavior of the material. The objective of this work is to characterize synthetic carbonate rocks through microtomography and petrography techniques, focusing on a comparative analysis before and after load application and degradation with a reactive fluid [1]. The synthetic rocks were subjected to physical characterization (mineralogy, computed tomography and porosity) and mechanical characterization (uniaxial compressive strength and Brazilian tests) before and after the dissolution process. The petrographic analysis verified an increase in both intergranular and intragranular porosities after dissolution. The microtomography analysis quantified the maximum increase in porosity, from 11.8% to 41.3% in the two-dimensional analysis and 31.6% to 52% in the three-dimensional analysis of the porous structures. Furthermore, the pores were quantified according to their area, and data was obtained on the orientation of the pores, providing insight into the preferred paths of fluid flow. It was also observed that the microtomography technique was an effective tool for characterizing fractures in the samples before and after dissolution [1]. Dissolution tests were also performed in a modified oedometer cell adapted to measure horizontal stress. The dissolution phase was conducted using water and an acid solution to evaluate the influence of the pH on the mechanical behaviour of the samples. When the sample in the oedometric cell is exposed to an acid solution under constant vertical load of 400kPa, vertical displacement takes place (volume decrease of the sample) and horizontal stress increases (Figure 1). The synthetic rock used in this experiment is mainly composed by calcite, with small additions of calcium hydroxide, and the reactive fluid is water acidified with acetic acid (with 10% concentration). This material is manufactured in laboratory in order to have greater control of its constituents and reproducibility of experimental results. During the acidification phase of the experiment, the sample was subjected to an acid flow with a pressure differential of 12kPa for 7h. The behavior in Figure 1 was also observed by [2] and [3]. The model for degradation of carbonatic soft rocks proposed by [2] was implemented in a finite element code capable of performing coupled THMC analyzes in porous media [4]. This model is based on the Critical State Theory with the introduction of a bonding variable that controls the size of the yield surface by modifying the tensile strength and the pre-consolidation stress of the material. In Figure 1 it is also possible to see that the HMC coupled simulation of the oedometric test was able to reproduce the experimental results in terms of volumetric strain and horizontal stress. In Figure 2 tomographic images of the synthetic carbonate rock before and after exposure to the acid solution in an oedometric cell under constant vertical load are presented. Such analyses are crucial for the injection of reactive fluids, such as CO2, at high depths. Dissolution of minerals will affect not only the porosity and permeability of the reservoir rock but also, possibly, the stress state in the vicinity of the injection well.

A Multiscale Hydro‐geochemical‐mechanical Approach to Analyze Faulted CO2 Reservoirs

Analysis of a Complex Faulted CO2 Reservoir Using a Three-dimensional Hydro-geochemical-Mechanical Approach

Three-dimensional Modeling of the Reactive Transport of CO 2 and Its Impact on Geomechanical Properties of Reservoir Rocks and Seals

Three-Dimensional Analysis of A Faulted Co2 Reservoir Using an Eshelby-Mori-Tanaka Approach to Rock Elastic Properties and Fault Permeability

CO2 storage in deep saline aquifers: evaluation of geomechanical risks using integrated modeling workflow

Thermal Impact of Co2 Injection on Geomechanical Response at the Futuregen 2.0 Site: A Three-Dimensional Thermo-Geomechanical Approach

Minerals Dissolution Effect on the Mechanical Properties of Synthetic Carbonate Rocks

Mass Transfer Analysis of CO2-Water-Rock Geochemical Reactions in Reservoirs

Pore–Scale Numerical Investigations of the Impact of Mineral Dissolution and Transport in Naturally Fractured Systems During CO2–Enriched Brine Injection

Uncertainty Quantification for Evaluating the Impacts of Fracture Zone on Pressure Build‐up and Ground Surface Uplift During Geological CO 2 Sequestration

Geomechanical Modelling Application to Support Reservoir Selection for Carbon Dioxide Utilization and Storage

Pore-Scale Simulation of Fracture Propagation by CO2 Flow Induced in Deep Shale Based on Hydro-Mechanical Coupled Model

Coupled Physical–Chemical Effects of CO2 on Rock Properties and Breakdown During Intermittent CO2-Hybrid Fracturing

Analyzing the Dynamics of Mineral Dissolution during Acid Fracturing by Pore-Scale Modeling of Acid-Rock Interaction

Three-Dimensional Coupled Temporal Geomechanical Model for Fault-Reactivation and Surface-Deformation Evaluation during Reservoir Depletion and CO2 Sequestration, Securing Long-Term Reservoir Sustainability

Control effect of fracture system on fluid migration, chemical reaction, and carbon dioxide storage

A Numerical Study of Fault Reactivation Mechanisms in CO2 Storage

Fracture Evolution during CO2 Fracturing in Unconventional Formations: A Simulation Study Using the Phase Field Method

Uncertainty Quantification for Evaluating Impacts of Caprock and Reservoir Properties on Pressure Buildup and Ground Surface Displacement During Geological CO2sequestration

Simulation of carbon dioxide mineralization and its effect on fault leakage rates in the South Georgia Rift Basin, Southeastern U.S.