Abstract:By defining the J integral and crack opening displacement (COD) under mixed mode I+II loading, a mixed J integral fracture criterion is proposed and the relationship between the J integral and COD in 40CrNiMo steel is discussed. The mixed J integral J(M) and its mode I and II components J(I) and J(II) were calculated by the finite element method, while the mixed COD and its mode I and II components CTOD and CTSD were measured using a duplicated grid. The critical values J(Mc) and CODc for mixed crack initiation were determined by a resistance curve. The results show that mode II loading lowers both JMc and CODc for 40CrNiMo steel. The variation of J(Mc) from mode I to mode II loading is found to be in accordance with the linked equations J(Mc) = J(II) + J(IIi); (JI(i)/J(Ic)) + (J(IIi)/J(IIc)) = 1, where J(Ic) and J(IIc) are the critical J integrals of pure mode I and II cracks, and J(Ii) and J(IIi) are the mode I and 11 components of J(Mc) at arbitrary mixed K-I/K-II, ratio respectively; the J(Mc) value for a given K-I/K-II ratio can be obtained if J(Ic) and J(IIc) are known. Finally, under valid loads, J(M) and the mixed COD satisfy the relation J(M) = J(I) + J(II) = d(n)sigma(0)CTOD + d(s)tau(0)CTSD. When unified by yield stress sigma(y) the relation becomes J(M) = dsigma(y)COD, where d(n), d(s) and d are coefficients, and sigma(0) and tau(0) are the tensile and shear stress at the crack tip strip respectively. While d(n) and d(s) vary with K-I/K-II ratio and materials, d was found to have a constant value of about 0(.)98.

DISCUSSION ON SEVERAL PROBLEMS IN J-INTEGRAL TESTING METHOD

Discussion on rationality of partial emendation in standard JIC test method

DISCUSSION ON RATIONALITY OF PARTIAL EMENDATION IN STANDARD J_(ⅠC) TEST METHOD

Analysis of the blunting line in ductile fracture toughness J（IC） test method

Blunting line equation in ductile fracture toughness JIC measurement

BLUNTING LINE EQUATION IN DUCTILE FRACTURE TOUGHNESS JⅠC MEASUREMENT

A NEW FORM OF BLUNTING LINE

J-Integral Evaluation for Interface Crack of Bimetal Loaded by Normal Three-Point Bending(Modeling & Simulation)

APPROACH TO MEASURING DUCTILE FRACTURE TOUGHNESS FOR SOME HIGHER TEARING RESISTANCE METALS

Some Problems in the J-integral

J Integral and Cod Fracture Criteria in 40crnimo Steel under Mixed Mode I+Ii Loading

Effect of Various Side Grooves on 3D Crack-Front J-Integral for CT Specimens

Improvements of J-Integral Criterion for Ductile Fracture Characterized by a Triaxiality Parameter

Recalibration and Clarification of the Formula Applied to the ISRM-Suggested CCNBD Specimens for Testing Rock Fracture Toughness

Quantifications of crack constraint effects in an austenitic steel

A Method of Fracture Toughness JIC Measurement Based on Digital Image Correlation and Acoustic Emission Technique

Constraint-Dependent J-R Curves of A Dissimilar Metal Welded Joint for Connecting Pipe-Nozzle of Nuclear Pressure Vessel

Study of the relationship between J-integral and COD parameters under mixed mode I + II loading in aluminum alloy Ly 12

A Modified Fracture Criterion for JIC

An Experimental Investigation of In-Plane Constraint Effect on Local Fracture Resistance of A Dissimilar Metal Welded Joint

Equivalent characterization of initial crack size of blunt notched components based on test data and physical model