Abstract:Abstract Central cracking in cross-wedge-rolled workpieces results in high wastage and economic loss. Recent cross-wedge rolling tests on two batches of steel showed that one batch formed central cracks, while the other was crack-free. The batches were both nominally of the same chemical composition and thermomechanical treatment history. In addition, both batches had passed all the standard quality assessments set for conventional forging processes. It was suspected that the different cracking behaviours were due to differences in microstructure between the two as-received steel billets, and the material in cross-wedge rolling (CWR) was more sensitive to the initial microstructure compared with other forging processes due to its specific loading condition including ostensibly compression and large plastic strain. Nevertheless, no previous study of this important problem could be identified. The aim of this study is, therefore, to identify the key microstructural features determining the central crack formation behaviour in CWR. The hot workability of the as-received billets was studied under uniaxial tensile conditions using a Gleeble 3800 test machine. Scanning electron microscope with energy-dispersive X-ray spectroscopy and electron backscatter diffraction was applied to characterise, quantitatively analyse, and compare the chemical composition, phase, grain, and inclusions in these two billets, both at room temperature and also at the CWR temperature (1080 °C). Non-metallic inclusions (oxides, sulphides, and silicates) in the billets were determined to be the main cause of the reported central cracking problem. The ductility of the steels at both room and elevated temperatures deteriorated markedly in the presence of the large volumes of inclusions. Grain boundary embrittlement occurred at the CWR temperature due to the aggregation of inclusions along the grain boundaries. It is suggested that a standard on specifying the inclusion quantity and size in CWR billets be established to produce crack-free products.

Chanism of Microcrack Formation of Fine Grain and High Strength Automotive Steel Plate During Cold Bending

Research on Microstructure and Property of Hot-Rolled 700MPa Grade Automobile Sheet

Microstructural effects on central crack formation in hot cross-wedge-rolled high-strength steel parts

Effect of Thermomechanical Controlled Processing on Microstructure and Cold Bending Properties of Automobile Beam Steel

Types and Cause of Cold Bending Crack Defects of Welded Pipe

Ex situ analysis of high-strength quenched and micro-alloyed steel during austenitising bending process: numerical simulation and experimental investigation

Simulation, microstructure and austenite reconstruction of a medium carbon micro-alloyed steel subjected to an austenitising bending process

Microstructural Dependence of Anisotropic Fracture Mechanisms in Cold-Drawn Pearlitic Steels

Microstructures and Mechanical Properties of Low Carbon Steel Hot Rolled in Ferrite Region Based on CSP Line

Importance of cold rolling and tempering on the microstructure evolution, precipitation behavior and mechanical responses of 9Cr3Co3W1Cu ferritic/martensitic steel

Insight into the impact of microstructure on crack initiation/propagation behavior in carbide-free bainitic steel during tensile deformation

Study on the Cracking Mechanism of YQ450NQR1 High-Strength Weathering Steel

Effect of Central Multiphase Microstructure of Thick Plates on Work Hardening and Crack Propagation

Study on the formation of alligator crack and edge crack in high silicon grain oriented electrical steel during cold rolling

Finite Element Simulation and Experiment on the Microstructure of High-Strength Mg-Gd-Y-Zn-Zr Alloy during U-Shaped Bending Process

Effects of rolling process and microstructure on the brittle crack initiation and arrest of a marine steel under low‐temperature

Microstructure distribution and bending fracture mechanism of 65Mn steel in the laser surface treatment

Mechanical properties and strengthening mechanism of high-strength low-carbon automobile steel plates produced by CSP technology

Design of a novel austenitising bending process in forming characteristics of high-strength quenched and micro-alloyed steel: Experiment and simulation

Microstructural Effect on Cold Strengthening Mechanism of MP159 Alloys

Tailoring the Microstructure to Enhance the Cryogenic Mechanical Properties of a Fe–34.5mn–0.04c Steel