Abstract:The organic and inorganic additives in PVC plastics cause great difficulties in their actual recycling process, which are different from pure PVC polymer (PVC-PO). In this study, PVC-PO and two commercial PVC plastics were selected and their differences in structure, pyrolysis behavior, chlorine release and migration were compared by FTIR, TG-MS and a fixed-bed pyrolysis reactor. There were more oxygen-containing functional groups and aromatic compounds in the commercial PVC plastics than PVC-PO because of the addition of foaming agents, flame retardants and lubricants. The thermal weight loss of the commercial PVC plastics was divided into three stages due to the decomposition of additives and the releases of CO2 gas, while that of the PVC-PO was two. The pyrolysis tar of two PVC plastics contained 35.72% and 15.71% oxygenated compounds, respectively, while that obtained from PVC-PO contained 96.46% of aromatic compounds. In addition, calcium additives in PVC plastics could promote the cracking of heavy constituents in the volatile, which was favorable for the formation of more light fractions in tar. The pyrolysis gas of PVC-PO was mainly composed of H2 and C1-C4 hydrocarbon gases, while that of PVC plastics contained about 50% of CO2, followed by H2 and hydrocarbon gases. The chlorine content of the PVC-PO (55.88 wt.%) was higher than that of the PVC plastics (13.83 wt.%, 22.77 wt.%). Most of the chlorine in the three PVC samples released as HCl at 220-370 degrees C, while the peak temperature of dechlorination of the PVC-PO delayed about 8 degrees C compared to that of PVC plastics and small part of HCl also released at around 475 degrees C in the pyrolysis of PVC-PO. About 99.90 wt.% of the chlorine was distributed in the gas phase after PVC-PO pyrolysis, while there were 99.85 wt.% and 97.85 wt.% of chlorine was detected in the gas products of two PVC plastics.

Inorganic chlorine released from typical components of medical waste in pyrolysis/incineration

Chlorine transfer in the pyrolysis of typical components of medical waste

Study on Pyrolysis of Medical Waste in a Rotary Kiln:Typical Component under Batch Feeding

PCDD/Fs Distribution Characteristics in Pyrolysis of Medical Waste with Different Composition and Chlorine Content

Effect of NaClO disinfectant treatment on the yields, components and combustion characteristics of typical medical waste pyrolysis products

Experimental Study on HC1 Real-time Emission Characteristics in Simulated Municipal Solid Waste Incineration

Comparative Study on Pyrolysis Behaviors and Chlorine Release of Pure PVC Polymer and Commercial PVC Plastics

Emissions of gaseous pollutants, polychlorinated dibenzo-p-dioxins, and polychlorinated dibenzo-furans from medical waste combustion in a batch fluidized-bed incinerator

Study on HCl Removal for Medical Waste Pyrolysis and Combustion Using a TG-FTIR Analyzer

Migration Characteristics of Inorganic Bromine During Incineration of Medical Waste

Study on the Evolution and Transformation of Chlorine During Co-Processing of Hazardous Waste Incineration Residue in a Cement Kiln

[Experimental and Mechanism Analyses on HCl Emission Control During PVC Combustion in Fixed Beds].

Experiments of PVC Gasification in a Fluidized Bed

Study on the Evolution and Transformation of Cl During Co-incineration of a Mixture of Rectification Residue and Raw Meal of a Cement Kiln.

Migration of inorganic chlorine during thermal treatment of mineralized waste

An Experimental Study on Pyrolysis Gas Characteristics of Typical Components of Medical Waste

Release of Hydrogen Chloride from Combustibles in Municipal Solid Waste.

Transformation behavior and fate of chlorine in polychloroprene (PCP) during its pyrolysis

HCl EMISSION DURING CHLORIDE WASTES COMBUSTION PROCESS

Experimental Study of Emission of HCl on Incinerating of Typical Municipal Solid Waste Components

[Effects of Chlorides on Cd Partitioning and Speciation in a Simulated MSW Incinerator].