Abstract:Thermal spray cermet based on tungsten carbide has been widely used due to its excellent wear resistance. The features of both carbide and binder phases are essential factors which determine the performance of cermet coating. The thermal cycling of WC–Co spray particles up to a temperature over the melting point of binder phase during thermal spraying involves the decarburization of carbide. The decarburization of carbide becomes severe with the decrease of carbide particle size, which makes it difficult yet to deposit a dense nanostructured WC–Co with a limited decarburization by thermal spraying. The decarburization not only reduces the wear-resistant phase but also leads to the formation of brittle Co–W–C ternary binder phase. Moreover, the limited decarburization involves the deposition of spray particle at a solid–liquid two-phase state with carbides at a solid state and metal binder in a molten state during spraying. High velocity impact of two-phase droplets as in high velocity oxy-fuel spraying (HVOF) results in the formation of a dense cermet coating and on the other hand leads to the possibility of rebounding of wear-resistant solid carbide particles. In this review article, the microstructural features of thermal spray WC–Co are examined based on the effect of the decarburization of tungsten carbide. The decarburization mechanisms of tungsten carbide are discussed for the control of decarburization of carbide. The effects of carbide particle size on the deposition process, adhesion of HVOF coating and wear performance of WC–Co coating as well are examined based on a solid–liquid two-phase deposition process. It is demonstrated that WC–Co cermet with different sizes of WC particles should be deposited by different processes. Moreover, the deposition of nanostructured WC–Co by thermal spraying and recent advances on the cold spraying of nanostructured WC–Co are introduced. The cold spraying with the proper design of spray powders will become promising process to deposit nanostructured WC–Co with pure cobalt binder with the hardness comparable to a sintered bulk and even high toughness of 18.9MPam1/2. The pure metastable metal binder phase evolved in the deposit makes it possible to deposit hard cermet through healing the non-bonded interfaces in the coating by post-spray annealing.

Study of Properties of Conventional and Nanostructured WC-12Co Coatings Deposited by HVOF

Microstructure Characterization and Abrasive Wear Performance of Hvof Sprayed Wc-Co Coatings

Effects Of Wc Crystal Characteristics On Microstructure And Mechanical Property Of Hvof-Sprayed Wc-Cocr Coatings

Effect of Flame Conditions on Abrasive Wear Performance of Hvof Sprayed Nanostructured Wc-12co Coatings

Characterization on microstructures and properties of WC-CoCr coating deposited by HVAF and HVOF processes

Thermal sprayed WC-Co coatings and their mechanical properties

Microstructure and mechanical property of high velocity oxy-fuel sprayed WC-Cr3C2-Ni coatings

Influence of WC Particle Size on the Mechanical Properties and Residual Stress of HVOF Thermally Sprayed WC–10Co–4Cr Coatings

Analysis of Microstructure of WC-12Co Coatings Prepared by the Three Kinds of Supersonic Thermal Spraying Processes

Study on Properties of Coatings Prepared by Supersonic Plasma Spraying with Three Kinds of WC-12Co Powder

Preparation And Properties Of Cold Sprayed Nano Wc-17co Coating On Magnesium Alloy

Promising WC-30WB-10Co Cemented Carbide Coating with Improved Density and Hardness Deposited by High Velocity Oxy-Fuel Spraying: Microstructure and Mechanical Properties

Microstructure and Tribological Properties of HVOF-Sprayed Nanostructured WC-12Co/Fe3O4 Coatings

Effects of Submicron WC Particles Addition on Wear Performances of HVOF Sprayed WC-Co Coatings

Characterization of Nano-Structured WC-Co Deposited by Cold Spraying

Relationships Between Feedstock Structure, Particle Parameter, Coating Deposition, Microstructure and Properties for Thermally Sprayed Conventional and Nanostructured WC–Co

Study on Wear Resistance of WC-Co and NiCr-Cr_2C_3 Coatings Sprayed by HVOF

Influence of HVO-AF Parameters and Particle Size on Elastic Modulus of WC-12Co Coatings

HVOF Spray Performance Optimization Analysis and Experimental Research of WC–12Co Coating on Ti Alloy

Wear resistance enhancement of HVOF-sprayed WC-Co coating by complete densification of starting powder

Effect of Cobalt and Chromium Content on Microstructure and Properties of WC-Co-Cr Coatings Prepared by High-Velocity Oxy-Fuel Spraying