Abstract:Marine water-lubricated bearing is the key part of the thrust shafting of underwater vehicles and some surface vessels, that is currently made with rubber, Thordon, Feroform, nylon, lignumvitae materials etc. Because the performance of vibration and noise reduction of the rubber material is better than some materials so that it is usually applied in water-lubricated propeller shaft bearing of submarines and underwater vehicles to improve their stealth, security, performance and reliability. Although the rubber is of better damping effect, it is always easy to cause friction vibration and noise under low speed, heavy load and wear situation, especially at starting or stopping phases. Therefore, it is of important theoretical significance and engineering value to enhance the mute level of the vehicles and alleviate friction vibration and noise.The tribological properties of water-lubricated rubber bearing such as friction and wear can affect the bearing vibration directly. So the research objective is to explore the influence of both friction and wear of water-lubricated rubber bearing on the bearing vibration under the different rubber materials of the bearing lining and working conditions. In the research, both theoretical analysis and test methods are applied. In theoretical analysis, the finite element model of the bearing is established and the deformation of the bearing lining is analyzed, and in test research, kinds of water-lubricated bearings with different rubber material were tested on the bearing test-bed under different shaft rotary speed, load and cooling water temperature. The research results show that both friction coefficient and wear of water lubricated rubber bearings are affected with the different rotary speed, load and cooling water temperature, which result in the bearing vibration status changed significantly. With the increase of the load in some range, the deformation of the bearing lining is intensified and the specific pressure of the bearing is decreased due to the augment of contact area of between test shaft and bearing lining so that the friction coefficient and vibration are declined. As cooling water temperature is enhanced, both wear and vibration are aggravated. The higher shaft rotary speed is, smaller friction coefficient is in certain speed range so friction vibration is reduced. (C) 2017 Elsevier B.V. All rights reserved.

Erosion Wear of Water Lubricated Rubber-Alloy Bearing when Taking Cavitation Effects into Consideration

Research on Erosion Wear to Water Lubricated Spiral Groove Rubber-Alloy Bearing Caused by Sand Particles

Experimental and Numerical Studies on Erosion Damage in Damping Holes on the Valve Plate of an Axial Piston Pump

Experimental and numerical study on the mixed lubrication performances of a new bearing

Effects of turbulence and bush wear on the transient tribo-dynamic characteristics of water-lubricated bearings

Investigation on the Micro Interface Lubrication Mechanism of Water Lubricated Bearing of Large Ships

Preliminary Study on Mechanism of Cavitation in Lubricant of Textured Sliding Bearing

Combined effect of cavitation and multi-scale texture on the bearing properties of seawater-lubricated friction pair

An Improved Eulerian-Lagrangian Method Combined with Ductile Material Model for Cavitation Erosion Assessment

Influence of Both Friction and Wear on the Vibration of Marine Water Lubricated Rubber Bearing

Study on the Effect of Cavitation on Tribological Performances of Sliding Bearing by CFD Method

A Dynamic Wear Model for Micro-Grooved Water-Lubricated Bearings under Transient Mixed Lubrication Condition

Influence of Cavitation and Shaft Deformation in the Analysis of Lubrication of the Stern Bearing

Two-dimensional Study of Lubrication Mechanism of Water-Lubricated Rubber Alloy Bearing

Effects of Texture Slip Surface on Load-Carrying Capacity and Cavitation of Bearing

Three Dimensional EHL Analyses for Water-lubricated Rubber Bearings with Grooves

A lubricated wear model for determining wear surface geometry on journal-bearing surfaces

Effects of Wear and Shaft-shape Error Defects on the Tribo-dynamic Response of Water-lubricated Bearings Under Propeller Disturbance

A Study on Static Characteristics for a Hybrid Journal-thrust Floating Ring Bearing with the Cavitations Influence

Numerical Simulation of Fluid-Structure Interaction of Marine Water-Lubricated Rubber Bearings

Mechanisms of abrasive wear in lubricated contacts