Abstract:Cr2AlB2 and Cr4AlB4 are members of the MAB phases that exhibit unique properties of both metals and ceramics. However, despite these unique characteristics, Cr2AlB2 and Cr4AlB4 phase coatings have not been widely investigated. In this study, Cr2AlB2 and Cr4AlB4 MAB phase coatings were fabricated by magnetron sputtering at room temperature and post-annealing. A composite target, consisting of a phase-pure disc-shaped CrB target overlapped by uniformly dispersed fan-shaped Al slices, was placed parallel to the substrates. The Al content of the coatings was adjusted by altering the areal proportion of the Al slices. MAB phases have crystallized upon post-annealing the as-deposited coatings on Al2O3(0001) substrates in Ar. The phase compositions and morphologies of the crystalline coatings were found to be dependent on the Al content and the annealing temperature. As-deposited coatings with a Cr:Al:B ratio close to 2:1:2 could crystallize as pure and dense Cr2AlB2 phases within the temperature range of 650–800 °C; higher annealing temperatures resulted in the decomposition of Cr2AlB2, while crystallization at lower temperatures was not evident from X-ray diffraction. As-deposited coatings with a Cr:Al:B ratio close to 3:1:3, despite containing a relatively higher Al content than required by the stoichiometry of Cr4AlB4, exhibited insufficient crystallization of Cr4AlB4 with unknown phases below 840 °C. Higher annealing temperatures resulted in the coexistence of Cr4AlB4 and CrB, indicating that achieving phase-pure and well-crystallized Cr4AlB4 coatings proved challenging, possibly due to the inevitable loss of Al during annealing. The configuration of the composite target and the substrates provides a promising strategy for fabricating phase-pure and dense Cr2AlB2 coatings.

Fabrication of Cr2AlC Coating from the Cost-Efficient Cr-Al-C Target by Arc Ion Plating

Properties of TiAlCrN coatings prepared by vacuum cathodic arc ion plating

Preparation of Al-Cr-Fe Coatings by Heat Treatment of Electrodeposited Cr/Al Composite Coatings

Al-Cr Coatings Prepared by Diffusion at Low Temperature and Its Phase Characterization

High Temperature Oxidation Behaviors of Al/Cr Composite Coating on Ti2AlNb Alloy

Fabrication of Cr2AlB2 and Cr4AlB4 MAB Phase Coatings by Magnetron Sputtering and Post-Annealing

Preparation of Single-Phase Ti2AlN Coating by Magnetron Sputtering with Cost-Efficient Hot-Pressed Ti-Al-N Targets

High-temperature Tribological Properties of a Novel AlFeCoNiCr-Cr3C2 Cermet Coatings

Effect of annealing on the microstructure, mechanical and electrochemical properties of CrAlC coatings

Effect of C doping on structure and properties of TiAlCrN coatings by filter cathode vacuum arc deposition

Microstructure and tribo-mechanical properties of APS-sprayed NiAl/Cr2AlC composite coatings with various additions of self-made Cr2AlC

Low-temperature Deposition of Al-rich Α-(Al, Cr)2O3 Films by Sputtering AlxCr95-x(α-Al2O3)5 Targets

Fabrication and Characterization of Plasma-Sprayed Cr3C2-25 Cr/Al2O3-40TiO2 Duplex Coating

High-Temperature Oxidation And Tensile Behaviors Of Cral Coating On Zirconium Alloy

Fabrication, microstructures and optical reflectivity of TiAlN/NiCr composite coating

Microstructure and Mechanical Properties of TiAlCrN and TiAlCrN/CrN Composite Coatings by Arc Ion Plating

Effect of CrN Addition on the Structure, Mechanical and Thermal Properties of Ti-Al-N Coating

Microstructure Evolution and Cyclic Oxidation Performance of Cr2AlC As Active Diffusion Barrier for NiCrAlY Coating on TiAl Alloy

Microstructure, Oxidation Behavior and Adhesion of a CoNiCrAlTaY Coating Deposited on a High Nb–TiAl Alloy by Plasma Surface Metallizing Technique

Microstructural and tribological characterization of NiAl matrix self-lubricating composite coatings by atmospheric plasma spraying

Influence of Al Content on the Microstructure and Properties of the CrAlN Coatings Deposited by Arc Ion Plating